Logo Search packages:      
Sourcecode: linux-fsl-imx51 version File versions  Download package

hub.c

/*
 * USB hub driver.
 *
 * (C) Copyright 1999 Linus Torvalds
 * (C) Copyright 1999 Johannes Erdfelt
 * (C) Copyright 1999 Gregory P. Smith
 * (C) Copyright 2001 Brad Hards (bhards@bigpond.net.au)
 *
 */

#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/module.h>
#include <linux/moduleparam.h>
#include <linux/completion.h>
#include <linux/sched.h>
#include <linux/list.h>
#include <linux/slab.h>
#include <linux/ioctl.h>
#include <linux/usb.h>
#include <linux/usbdevice_fs.h>
#include <linux/kthread.h>
#include <linux/mutex.h>
#include <linux/freezer.h>

#include <asm/uaccess.h>
#include <asm/byteorder.h>

#include "usb.h"
#include "hcd.h"
#include "hub.h"

/* if we are in debug mode, always announce new devices */
#ifdef DEBUG
#ifndef CONFIG_USB_ANNOUNCE_NEW_DEVICES
#define CONFIG_USB_ANNOUNCE_NEW_DEVICES
#endif
#endif

00040 struct usb_hub {
      struct device           *intfdev;   /* the "interface" device */
      struct usb_device *hdev;
      struct kref       kref;
      struct urb        *urb;       /* for interrupt polling pipe */

      /* buffer for urb ... with extra space in case of babble */
      char              (*buffer)[8];
      dma_addr_t        buffer_dma; /* DMA address for buffer */
      union {
            struct usb_hub_status   hub;
            struct usb_port_status  port;
      }                 *status;    /* buffer for status reports */
      struct mutex            status_mutex;     /* for the status buffer */

      int               error;            /* last reported error */
      int               nerrors;    /* track consecutive errors */

      struct list_head  event_list; /* hubs w/data or errs ready */
      unsigned long           event_bits[1];    /* status change bitmask */
      unsigned long           change_bits[1];   /* ports with logical connect
                                          status change */
      unsigned long           busy_bits[1];     /* ports being reset or
                                          resumed */
#if USB_MAXCHILDREN > 31 /* 8*sizeof(unsigned long) - 1 */
#error event_bits[] is too short!
#endif

      struct usb_hub_descriptor *descriptor;    /* class descriptor */
      struct usb_tt           tt;         /* Transaction Translator */

      unsigned          mA_per_port;      /* current for each child */

      unsigned          limited_power:1;
      unsigned          quiescing:1;
      unsigned          disconnected:1;

      unsigned          has_indicators:1;
      u8                indicator[USB_MAXCHILDREN];
      struct delayed_work     leds;
      struct delayed_work     init_work;
};


/* Protect struct usb_device->state and ->children members
 * Note: Both are also protected by ->dev.sem, except that ->state can
 * change to USB_STATE_NOTATTACHED even when the semaphore isn't held. */
static DEFINE_SPINLOCK(device_state_lock);

/* khubd's worklist and its lock */
static DEFINE_SPINLOCK(hub_event_lock);
static LIST_HEAD(hub_event_list);   /* List of hubs needing servicing */

/* Wakes up khubd */
static DECLARE_WAIT_QUEUE_HEAD(khubd_wait);

static struct task_struct *khubd_task;

/* cycle leds on hubs that aren't blinking for attention */
static int blinkenlights = 0;
module_param (blinkenlights, bool, S_IRUGO);
MODULE_PARM_DESC (blinkenlights, "true to cycle leds on hubs");

/*
 * Device SATA8000 FW1.0 from DATAST0R Technology Corp requires about
 * 10 seconds to send reply for the initial 64-byte descriptor request.
 */
/* define initial 64-byte descriptor request timeout in milliseconds */
static int initial_descriptor_timeout = USB_CTRL_GET_TIMEOUT;
module_param(initial_descriptor_timeout, int, S_IRUGO|S_IWUSR);
MODULE_PARM_DESC(initial_descriptor_timeout,
            "initial 64-byte descriptor request timeout in milliseconds "
            "(default 5000 - 5.0 seconds)");

/*
 * As of 2.6.10 we introduce a new USB device initialization scheme which
 * closely resembles the way Windows works.  Hopefully it will be compatible
 * with a wider range of devices than the old scheme.  However some previously
 * working devices may start giving rise to "device not accepting address"
 * errors; if that happens the user can try the old scheme by adjusting the
 * following module parameters.
 *
 * For maximum flexibility there are two boolean parameters to control the
 * hub driver's behavior.  On the first initialization attempt, if the
 * "old_scheme_first" parameter is set then the old scheme will be used,
 * otherwise the new scheme is used.  If that fails and "use_both_schemes"
 * is set, then the driver will make another attempt, using the other scheme.
 */
static int old_scheme_first = 0;
module_param(old_scheme_first, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(old_scheme_first,
             "start with the old device initialization scheme");

static int use_both_schemes = 1;
module_param(use_both_schemes, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(use_both_schemes,
            "try the other device initialization scheme if the "
            "first one fails");

/* Mutual exclusion for EHCI CF initialization.  This interferes with
 * port reset on some companion controllers.
 */
DECLARE_RWSEM(ehci_cf_port_reset_rwsem);
EXPORT_SYMBOL_GPL(ehci_cf_port_reset_rwsem);

#define HUB_DEBOUNCE_TIMEOUT  1500
#define HUB_DEBOUNCE_STEP       25
#define HUB_DEBOUNCE_STABLE    100


static int usb_reset_and_verify_device(struct usb_device *udev);

static inline char *portspeed(int portstatus)
{
      if (portstatus & (1 << USB_PORT_FEAT_HIGHSPEED))
            return "480 Mb/s";
      else if (portstatus & (1 << USB_PORT_FEAT_LOWSPEED))
            return "1.5 Mb/s";
      else if (portstatus & (1 << USB_PORT_FEAT_SUPERSPEED))
            return "5.0 Gb/s";
      else
            return "12 Mb/s";
}

/* Note that hdev or one of its children must be locked! */
static inline struct usb_hub *hdev_to_hub(struct usb_device *hdev)
{
      return usb_get_intfdata(hdev->actconfig->interface[0]);
}

/* USB 2.0 spec Section 11.24.4.5 */
static int get_hub_descriptor(struct usb_device *hdev, void *data, int size)
{
      int i, ret;

      for (i = 0; i < 3; i++) {
            ret = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0),
                  USB_REQ_GET_DESCRIPTOR, USB_DIR_IN | USB_RT_HUB,
                  USB_DT_HUB << 8, 0, data, size,
                  USB_CTRL_GET_TIMEOUT);
            if (ret >= (USB_DT_HUB_NONVAR_SIZE + 2))
                  return ret;
      }
      return -EINVAL;
}

/*
 * USB 2.0 spec Section 11.24.2.1
 */
static int clear_hub_feature(struct usb_device *hdev, int feature)
{
      return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
            USB_REQ_CLEAR_FEATURE, USB_RT_HUB, feature, 0, NULL, 0, 1000);
}

/*
 * USB 2.0 spec Section 11.24.2.2
 */
static int clear_port_feature(struct usb_device *hdev, int port1, int feature)
{
      return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
            USB_REQ_CLEAR_FEATURE, USB_RT_PORT, feature, port1,
            NULL, 0, 1000);
}

/*
 * USB 2.0 spec Section 11.24.2.13
 */
static int set_port_feature(struct usb_device *hdev, int port1, int feature)
{
      return usb_control_msg(hdev, usb_sndctrlpipe(hdev, 0),
            USB_REQ_SET_FEATURE, USB_RT_PORT, feature, port1,
            NULL, 0, 1000);
}

/*
 * USB 2.0 spec Section 11.24.2.7.1.10 and table 11-7
 * for info about using port indicators
 */
static void set_port_led(
      struct usb_hub *hub,
      int port1,
      int selector
)
{
      int status = set_port_feature(hub->hdev, (selector << 8) | port1,
                  USB_PORT_FEAT_INDICATOR);
      if (status < 0)
            dev_dbg (hub->intfdev,
                  "port %d indicator %s status %d\n",
                  port1,
                  ({ char *s; switch (selector) {
                  case HUB_LED_AMBER: s = "amber"; break;
                  case HUB_LED_GREEN: s = "green"; break;
                  case HUB_LED_OFF: s = "off"; break;
                  case HUB_LED_AUTO: s = "auto"; break;
                  default: s = "??"; break;
                  }; s; }),
                  status);
}

#define     LED_CYCLE_PERIOD  ((2*HZ)/3)

static void led_work (struct work_struct *work)
{
      struct usb_hub          *hub =
            container_of(work, struct usb_hub, leds.work);
      struct usb_device *hdev = hub->hdev;
      unsigned          i;
      unsigned          changed = 0;
      int               cursor = -1;

      if (hdev->state != USB_STATE_CONFIGURED || hub->quiescing)
            return;

      for (i = 0; i < hub->descriptor->bNbrPorts; i++) {
            unsigned    selector, mode;

            /* 30%-50% duty cycle */

            switch (hub->indicator[i]) {
            /* cycle marker */
            case INDICATOR_CYCLE:
                  cursor = i;
                  selector = HUB_LED_AUTO;
                  mode = INDICATOR_AUTO;
                  break;
            /* blinking green = sw attention */
            case INDICATOR_GREEN_BLINK:
                  selector = HUB_LED_GREEN;
                  mode = INDICATOR_GREEN_BLINK_OFF;
                  break;
            case INDICATOR_GREEN_BLINK_OFF:
                  selector = HUB_LED_OFF;
                  mode = INDICATOR_GREEN_BLINK;
                  break;
            /* blinking amber = hw attention */
            case INDICATOR_AMBER_BLINK:
                  selector = HUB_LED_AMBER;
                  mode = INDICATOR_AMBER_BLINK_OFF;
                  break;
            case INDICATOR_AMBER_BLINK_OFF:
                  selector = HUB_LED_OFF;
                  mode = INDICATOR_AMBER_BLINK;
                  break;
            /* blink green/amber = reserved */
            case INDICATOR_ALT_BLINK:
                  selector = HUB_LED_GREEN;
                  mode = INDICATOR_ALT_BLINK_OFF;
                  break;
            case INDICATOR_ALT_BLINK_OFF:
                  selector = HUB_LED_AMBER;
                  mode = INDICATOR_ALT_BLINK;
                  break;
            default:
                  continue;
            }
            if (selector != HUB_LED_AUTO)
                  changed = 1;
            set_port_led(hub, i + 1, selector);
            hub->indicator[i] = mode;
      }
      if (!changed && blinkenlights) {
            cursor++;
            cursor %= hub->descriptor->bNbrPorts;
            set_port_led(hub, cursor + 1, HUB_LED_GREEN);
            hub->indicator[cursor] = INDICATOR_CYCLE;
            changed++;
      }
      if (changed)
            schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD);
}

/* use a short timeout for hub/port status fetches */
#define     USB_STS_TIMEOUT         1000
#define     USB_STS_RETRIES         5

/*
 * USB 2.0 spec Section 11.24.2.6
 */
static int get_hub_status(struct usb_device *hdev,
            struct usb_hub_status *data)
{
      int i, status = -ETIMEDOUT;

      for (i = 0; i < USB_STS_RETRIES && status == -ETIMEDOUT; i++) {
            status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0),
                  USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_HUB, 0, 0,
                  data, sizeof(*data), USB_STS_TIMEOUT);
      }
      return status;
}

/*
 * USB 2.0 spec Section 11.24.2.7
 */
static int get_port_status(struct usb_device *hdev, int port1,
            struct usb_port_status *data)
{
      int i, status = -ETIMEDOUT;

      for (i = 0; i < USB_STS_RETRIES && status == -ETIMEDOUT; i++) {
            status = usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0),
                  USB_REQ_GET_STATUS, USB_DIR_IN | USB_RT_PORT, 0, port1,
                  data, sizeof(*data), USB_STS_TIMEOUT);
      }
      return status;
}

static int hub_port_status(struct usb_hub *hub, int port1,
            u16 *status, u16 *change)
{
      int ret;

      mutex_lock(&hub->status_mutex);
      ret = get_port_status(hub->hdev, port1, &hub->status->port);
      if (ret < 4) {
            dev_err(hub->intfdev,
                  "%s failed (err = %d)\n", __func__, ret);
            if (ret >= 0)
                  ret = -EIO;
      } else {
            *status = le16_to_cpu(hub->status->port.wPortStatus);
            *change = le16_to_cpu(hub->status->port.wPortChange);
            ret = 0;
      }
      mutex_unlock(&hub->status_mutex);
      return ret;
}

static void kick_khubd(struct usb_hub *hub)
{
      unsigned long     flags;

      /* Suppress autosuspend until khubd runs */
      to_usb_interface(hub->intfdev)->pm_usage_cnt = 1;

      spin_lock_irqsave(&hub_event_lock, flags);
      if (!hub->disconnected && list_empty(&hub->event_list)) {
            list_add_tail(&hub->event_list, &hub_event_list);
            wake_up(&khubd_wait);
      }
      spin_unlock_irqrestore(&hub_event_lock, flags);
}

void usb_kick_khubd(struct usb_device *hdev)
{
      /* FIXME: What if hdev isn't bound to the hub driver? */
      kick_khubd(hdev_to_hub(hdev));
}


/* completion function, fires on port status changes and various faults */
static void hub_irq(struct urb *urb)
{
      struct usb_hub *hub = urb->context;
      int status = urb->status;
      unsigned i;
      unsigned long bits;

      switch (status) {
      case -ENOENT:           /* synchronous unlink */
      case -ECONNRESET: /* async unlink */
      case -ESHUTDOWN:  /* hardware going away */
            return;

      default:          /* presumably an error */
            /* Cause a hub reset after 10 consecutive errors */
            dev_dbg (hub->intfdev, "transfer --> %d\n", status);
            if ((++hub->nerrors < 10) || hub->error)
                  goto resubmit;
            hub->error = status;
            /* FALL THROUGH */

      /* let khubd handle things */
      case 0:                 /* we got data:  port status changed */
            bits = 0;
            for (i = 0; i < urb->actual_length; ++i)
                  bits |= ((unsigned long) ((*hub->buffer)[i]))
                              << (i*8);
            hub->event_bits[0] = bits;
            break;
      }

      hub->nerrors = 0;

      /* Something happened, let khubd figure it out */
      kick_khubd(hub);

resubmit:
      if (hub->quiescing)
            return;

      if ((status = usb_submit_urb (hub->urb, GFP_ATOMIC)) != 0
                  && status != -ENODEV && status != -EPERM)
            dev_err (hub->intfdev, "resubmit --> %d\n", status);
}

/* USB 2.0 spec Section 11.24.2.3 */
static inline int
hub_clear_tt_buffer (struct usb_device *hdev, u16 devinfo, u16 tt)
{
      return usb_control_msg(hdev, usb_rcvctrlpipe(hdev, 0),
                         HUB_CLEAR_TT_BUFFER, USB_RT_PORT, devinfo,
                         tt, NULL, 0, 1000);
}

/*
 * enumeration blocks khubd for a long time. we use keventd instead, since
 * long blocking there is the exception, not the rule.  accordingly, HCDs
 * talking to TTs must queue control transfers (not just bulk and iso), so
 * both can talk to the same hub concurrently.
 */
static void hub_tt_work(struct work_struct *work)
{
      struct usb_hub          *hub =
            container_of(work, struct usb_hub, tt.clear_work);
      unsigned long           flags;
      int               limit = 100;

      spin_lock_irqsave (&hub->tt.lock, flags);
      while (--limit && !list_empty (&hub->tt.clear_list)) {
            struct list_head  *next;
            struct usb_tt_clear     *clear;
            struct usb_device *hdev = hub->hdev;
            const struct hc_driver  *drv;
            int               status;

            next = hub->tt.clear_list.next;
            clear = list_entry (next, struct usb_tt_clear, clear_list);
            list_del (&clear->clear_list);

            /* drop lock so HCD can concurrently report other TT errors */
            spin_unlock_irqrestore (&hub->tt.lock, flags);
            status = hub_clear_tt_buffer (hdev, clear->devinfo, clear->tt);
            if (status)
                  dev_err (&hdev->dev,
                        "clear tt %d (%04x) error %d\n",
                        clear->tt, clear->devinfo, status);

            /* Tell the HCD, even if the operation failed */
            drv = clear->hcd->driver;
            if (drv->clear_tt_buffer_complete)
                  (drv->clear_tt_buffer_complete)(clear->hcd, clear->ep);

            kfree(clear);
            spin_lock_irqsave(&hub->tt.lock, flags);
      }
      spin_unlock_irqrestore (&hub->tt.lock, flags);
}

/**
 * usb_hub_clear_tt_buffer - clear control/bulk TT state in high speed hub
 * @urb: an URB associated with the failed or incomplete split transaction
 *
 * High speed HCDs use this to tell the hub driver that some split control or
 * bulk transaction failed in a way that requires clearing internal state of
 * a transaction translator.  This is normally detected (and reported) from
 * interrupt context.
 *
 * It may not be possible for that hub to handle additional full (or low)
 * speed transactions until that state is fully cleared out.
 */
int usb_hub_clear_tt_buffer(struct urb *urb)
{
      struct usb_device *udev = urb->dev;
      int               pipe = urb->pipe;
      struct usb_tt           *tt = udev->tt;
      unsigned long           flags;
      struct usb_tt_clear     *clear;

      /* we've got to cope with an arbitrary number of pending TT clears,
       * since each TT has "at least two" buffers that can need it (and
       * there can be many TTs per hub).  even if they're uncommon.
       */
      if ((clear = kmalloc (sizeof *clear, GFP_ATOMIC)) == NULL) {
            dev_err (&udev->dev, "can't save CLEAR_TT_BUFFER state\n");
            /* FIXME recover somehow ... RESET_TT? */
            return -ENOMEM;
      }

      /* info that CLEAR_TT_BUFFER needs */
      clear->tt = tt->multi ? udev->ttport : 1;
      clear->devinfo = usb_pipeendpoint (pipe);
      clear->devinfo |= udev->devnum << 4;
      clear->devinfo |= usb_pipecontrol (pipe)
                  ? (USB_ENDPOINT_XFER_CONTROL << 11)
                  : (USB_ENDPOINT_XFER_BULK << 11);
      if (usb_pipein (pipe))
            clear->devinfo |= 1 << 15;

      /* info for completion callback */
      clear->hcd = bus_to_hcd(udev->bus);
      clear->ep = urb->ep;

      /* tell keventd to clear state for this TT */
      spin_lock_irqsave (&tt->lock, flags);
      list_add_tail (&clear->clear_list, &tt->clear_list);
      schedule_work(&tt->clear_work);
      spin_unlock_irqrestore (&tt->lock, flags);
      return 0;
}
EXPORT_SYMBOL_GPL(usb_hub_clear_tt_buffer);

/* If do_delay is false, return the number of milliseconds the caller
 * needs to delay.
 */
static unsigned hub_power_on(struct usb_hub *hub, bool do_delay)
{
      int port1;
      unsigned pgood_delay = hub->descriptor->bPwrOn2PwrGood * 2;
      unsigned delay;
      u16 wHubCharacteristics =
                  le16_to_cpu(hub->descriptor->wHubCharacteristics);

      /* Enable power on each port.  Some hubs have reserved values
       * of LPSM (> 2) in their descriptors, even though they are
       * USB 2.0 hubs.  Some hubs do not implement port-power switching
       * but only emulate it.  In all cases, the ports won't work
       * unless we send these messages to the hub.
       */
      if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2)
            dev_dbg(hub->intfdev, "enabling power on all ports\n");
      else
            dev_dbg(hub->intfdev, "trying to enable port power on "
                        "non-switchable hub\n");
      for (port1 = 1; port1 <= hub->descriptor->bNbrPorts; port1++)
            set_port_feature(hub->hdev, port1, USB_PORT_FEAT_POWER);

      /* Wait at least 100 msec for power to become stable */
      delay = max(pgood_delay, (unsigned) 100);
      if (do_delay)
            msleep(delay);
      return delay;
}

static int hub_hub_status(struct usb_hub *hub,
            u16 *status, u16 *change)
{
      int ret;

      mutex_lock(&hub->status_mutex);
      ret = get_hub_status(hub->hdev, &hub->status->hub);
      if (ret < 0)
            dev_err (hub->intfdev,
                  "%s failed (err = %d)\n", __func__, ret);
      else {
            *status = le16_to_cpu(hub->status->hub.wHubStatus);
            *change = le16_to_cpu(hub->status->hub.wHubChange); 
            ret = 0;
      }
      mutex_unlock(&hub->status_mutex);
      return ret;
}

static int hub_port_disable(struct usb_hub *hub, int port1, int set_state)
{
      struct usb_device *hdev = hub->hdev;
      int ret = 0;

      if (hdev->children[port1-1] && set_state)
            usb_set_device_state(hdev->children[port1-1],
                        USB_STATE_NOTATTACHED);
      if (!hub->error)
            ret = clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE);
      if (ret)
            dev_err(hub->intfdev, "cannot disable port %d (err = %d)\n",
                        port1, ret);
      return ret;
}

/*
 * Disable a port and mark a logical connnect-change event, so that some
 * time later khubd will disconnect() any existing usb_device on the port
 * and will re-enumerate if there actually is a device attached.
 */
static void hub_port_logical_disconnect(struct usb_hub *hub, int port1)
{
      dev_dbg(hub->intfdev, "logical disconnect on port %d\n", port1);
      hub_port_disable(hub, port1, 1);

      /* FIXME let caller ask to power down the port:
       *  - some devices won't enumerate without a VBUS power cycle
       *  - SRP saves power that way
       *  - ... new call, TBD ...
       * That's easy if this hub can switch power per-port, and
       * khubd reactivates the port later (timer, SRP, etc).
       * Powerdown must be optional, because of reset/DFU.
       */

      set_bit(port1, hub->change_bits);
      kick_khubd(hub);
}

enum hub_activation_type {
      HUB_INIT, HUB_INIT2, HUB_INIT3,
      HUB_POST_RESET, HUB_RESUME, HUB_RESET_RESUME,
};

static void hub_init_func2(struct work_struct *ws);
static void hub_init_func3(struct work_struct *ws);

static void hub_activate(struct usb_hub *hub, enum hub_activation_type type)
{
      struct usb_device *hdev = hub->hdev;
      int port1;
      int status;
      bool need_debounce_delay = false;
      unsigned delay;

      /* Continue a partial initialization */
      if (type == HUB_INIT2)
            goto init2;
      if (type == HUB_INIT3)
            goto init3;

      /* After a resume, port power should still be on.
       * For any other type of activation, turn it on.
       */
      if (type != HUB_RESUME) {

            /* Speed up system boot by using a delayed_work for the
             * hub's initial power-up delays.  This is pretty awkward
             * and the implementation looks like a home-brewed sort of
             * setjmp/longjmp, but it saves at least 100 ms for each
             * root hub (assuming usbcore is compiled into the kernel
             * rather than as a module).  It adds up.
             *
             * This can't be done for HUB_RESUME or HUB_RESET_RESUME
             * because for those activation types the ports have to be
             * operational when we return.  In theory this could be done
             * for HUB_POST_RESET, but it's easier not to.
             */
            if (type == HUB_INIT) {
                  delay = hub_power_on(hub, false);
                  PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func2);
                  schedule_delayed_work(&hub->init_work,
                              msecs_to_jiffies(delay));

                  /* Suppress autosuspend until init is done */
                  to_usb_interface(hub->intfdev)->pm_usage_cnt = 1;
                  return;           /* Continues at init2: below */
            } else {
                  hub_power_on(hub, true);
            }
      }
 init2:

      /* Check each port and set hub->change_bits to let khubd know
       * which ports need attention.
       */
      for (port1 = 1; port1 <= hdev->maxchild; ++port1) {
            struct usb_device *udev = hdev->children[port1-1];
            u16 portstatus, portchange;

            portstatus = portchange = 0;
            status = hub_port_status(hub, port1, &portstatus, &portchange);
            if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
                  dev_dbg(hub->intfdev,
                              "port %d: status %04x change %04x\n",
                              port1, portstatus, portchange);

            /* After anything other than HUB_RESUME (i.e., initialization
             * or any sort of reset), every port should be disabled.
             * Unconnected ports should likewise be disabled (paranoia),
             * and so should ports for which we have no usb_device.
             */
            if ((portstatus & USB_PORT_STAT_ENABLE) && (
                        type != HUB_RESUME ||
                        !(portstatus & USB_PORT_STAT_CONNECTION) ||
                        !udev ||
                        udev->state == USB_STATE_NOTATTACHED)) {
                  clear_port_feature(hdev, port1, USB_PORT_FEAT_ENABLE);
                  portstatus &= ~USB_PORT_STAT_ENABLE;
            }

            /* Clear status-change flags; we'll debounce later */
            if (portchange & USB_PORT_STAT_C_CONNECTION) {
                  need_debounce_delay = true;
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_CONNECTION);
            }
            if (portchange & USB_PORT_STAT_C_ENABLE) {
                  need_debounce_delay = true;
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_ENABLE);
            }

            if (!udev || udev->state == USB_STATE_NOTATTACHED) {
                  /* Tell khubd to disconnect the device or
                   * check for a new connection
                   */
                  if (udev || (portstatus & USB_PORT_STAT_CONNECTION))
                        set_bit(port1, hub->change_bits);

            } else if (portstatus & USB_PORT_STAT_ENABLE) {
                  /* The power session apparently survived the resume.
                   * If there was an overcurrent or suspend change
                   * (i.e., remote wakeup request), have khubd
                   * take care of it.
                   */
                  if (portchange)
                        set_bit(port1, hub->change_bits);

            } else if (udev->persist_enabled) {
#ifdef CONFIG_PM
                  udev->reset_resume = 1;
#endif
                  set_bit(port1, hub->change_bits);

            } else {
                  /* The power session is gone; tell khubd */
                  usb_set_device_state(udev, USB_STATE_NOTATTACHED);
                  set_bit(port1, hub->change_bits);
            }
      }

      /* If no port-status-change flags were set, we don't need any
       * debouncing.  If flags were set we can try to debounce the
       * ports all at once right now, instead of letting khubd do them
       * one at a time later on.
       *
       * If any port-status changes do occur during this delay, khubd
       * will see them later and handle them normally.
       */
      if (need_debounce_delay) {
            delay = HUB_DEBOUNCE_STABLE;

            /* Don't do a long sleep inside a workqueue routine */
            if (type == HUB_INIT2) {
                  PREPARE_DELAYED_WORK(&hub->init_work, hub_init_func3);
                  schedule_delayed_work(&hub->init_work,
                              msecs_to_jiffies(delay));
                  return;           /* Continues at init3: below */
            } else {
                  msleep(delay);
            }
      }
 init3:
      hub->quiescing = 0;

      status = usb_submit_urb(hub->urb, GFP_NOIO);
      if (status < 0)
            dev_err(hub->intfdev, "activate --> %d\n", status);
      if (hub->has_indicators && blinkenlights)
            schedule_delayed_work(&hub->leds, LED_CYCLE_PERIOD);

      /* Scan all ports that need attention */
      kick_khubd(hub);
}

/* Implement the continuations for the delays above */
static void hub_init_func2(struct work_struct *ws)
{
      struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work);

      hub_activate(hub, HUB_INIT2);
}

static void hub_init_func3(struct work_struct *ws)
{
      struct usb_hub *hub = container_of(ws, struct usb_hub, init_work.work);

      hub_activate(hub, HUB_INIT3);
}

enum hub_quiescing_type {
      HUB_DISCONNECT, HUB_PRE_RESET, HUB_SUSPEND
};

static void hub_quiesce(struct usb_hub *hub, enum hub_quiescing_type type)
{
      struct usb_device *hdev = hub->hdev;
      int i;

      cancel_delayed_work_sync(&hub->init_work);

      /* khubd and related activity won't re-trigger */
      hub->quiescing = 1;

      if (type != HUB_SUSPEND) {
            /* Disconnect all the children */
            for (i = 0; i < hdev->maxchild; ++i) {
                  if (hdev->children[i])
                        usb_disconnect(&hdev->children[i]);
            }
      }

      /* Stop khubd and related activity */
      usb_kill_urb(hub->urb);
      if (hub->has_indicators)
            cancel_delayed_work_sync(&hub->leds);
      if (hub->tt.hub)
            cancel_work_sync(&hub->tt.clear_work);
}

/* caller has locked the hub device */
static int hub_pre_reset(struct usb_interface *intf)
{
      struct usb_hub *hub = usb_get_intfdata(intf);

      hub_quiesce(hub, HUB_PRE_RESET);
      return 0;
}

/* caller has locked the hub device */
static int hub_post_reset(struct usb_interface *intf)
{
      struct usb_hub *hub = usb_get_intfdata(intf);

      hub_activate(hub, HUB_POST_RESET);
      return 0;
}

static int hub_configure(struct usb_hub *hub,
      struct usb_endpoint_descriptor *endpoint)
{
      struct usb_device *hdev = hub->hdev;
      struct device *hub_dev = hub->intfdev;
      u16 hubstatus, hubchange;
      u16 wHubCharacteristics;
      unsigned int pipe;
      int maxp, ret;
      char *message;

      hub->buffer = usb_buffer_alloc(hdev, sizeof(*hub->buffer), GFP_KERNEL,
                  &hub->buffer_dma);
      if (!hub->buffer) {
            message = "can't allocate hub irq buffer";
            ret = -ENOMEM;
            goto fail;
      }

      hub->status = kmalloc(sizeof(*hub->status), GFP_KERNEL);
      if (!hub->status) {
            message = "can't kmalloc hub status buffer";
            ret = -ENOMEM;
            goto fail;
      }
      mutex_init(&hub->status_mutex);

      hub->descriptor = kmalloc(sizeof(*hub->descriptor), GFP_KERNEL);
      if (!hub->descriptor) {
            message = "can't kmalloc hub descriptor";
            ret = -ENOMEM;
            goto fail;
      }

      /* Request the entire hub descriptor.
       * hub->descriptor can handle USB_MAXCHILDREN ports,
       * but the hub can/will return fewer bytes here.
       */
      ret = get_hub_descriptor(hdev, hub->descriptor,
                  sizeof(*hub->descriptor));
      if (ret < 0) {
            message = "can't read hub descriptor";
            goto fail;
      } else if (hub->descriptor->bNbrPorts > USB_MAXCHILDREN) {
            message = "hub has too many ports!";
            ret = -ENODEV;
            goto fail;
      }

      hdev->maxchild = hub->descriptor->bNbrPorts;
      dev_info (hub_dev, "%d port%s detected\n", hdev->maxchild,
            (hdev->maxchild == 1) ? "" : "s");

      wHubCharacteristics = le16_to_cpu(hub->descriptor->wHubCharacteristics);

      if (wHubCharacteristics & HUB_CHAR_COMPOUND) {
            int   i;
            char  portstr [USB_MAXCHILDREN + 1];

            for (i = 0; i < hdev->maxchild; i++)
                  portstr[i] = hub->descriptor->DeviceRemovable
                            [((i + 1) / 8)] & (1 << ((i + 1) % 8))
                        ? 'F' : 'R';
            portstr[hdev->maxchild] = 0;
            dev_dbg(hub_dev, "compound device; port removable status: %s\n", portstr);
      } else
            dev_dbg(hub_dev, "standalone hub\n");

      switch (wHubCharacteristics & HUB_CHAR_LPSM) {
            case 0x00:
                  dev_dbg(hub_dev, "ganged power switching\n");
                  break;
            case 0x01:
                  dev_dbg(hub_dev, "individual port power switching\n");
                  break;
            case 0x02:
            case 0x03:
                  dev_dbg(hub_dev, "no power switching (usb 1.0)\n");
                  break;
      }

      switch (wHubCharacteristics & HUB_CHAR_OCPM) {
            case 0x00:
                  dev_dbg(hub_dev, "global over-current protection\n");
                  break;
            case 0x08:
                  dev_dbg(hub_dev, "individual port over-current protection\n");
                  break;
            case 0x10:
            case 0x18:
                  dev_dbg(hub_dev, "no over-current protection\n");
                        break;
      }

      spin_lock_init (&hub->tt.lock);
      INIT_LIST_HEAD (&hub->tt.clear_list);
      INIT_WORK(&hub->tt.clear_work, hub_tt_work);
      switch (hdev->descriptor.bDeviceProtocol) {
            case 0:
                  break;
            case 1:
                  dev_dbg(hub_dev, "Single TT\n");
                  hub->tt.hub = hdev;
                  break;
            case 2:
                  ret = usb_set_interface(hdev, 0, 1);
                  if (ret == 0) {
                        dev_dbg(hub_dev, "TT per port\n");
                        hub->tt.multi = 1;
                  } else
                        dev_err(hub_dev, "Using single TT (err %d)\n",
                              ret);
                  hub->tt.hub = hdev;
                  break;
            case 3:
                  /* USB 3.0 hubs don't have a TT */
                  break;
            default:
                  dev_dbg(hub_dev, "Unrecognized hub protocol %d\n",
                        hdev->descriptor.bDeviceProtocol);
                  break;
      }

      /* Note 8 FS bit times == (8 bits / 12000000 bps) ~= 666ns */
      switch (wHubCharacteristics & HUB_CHAR_TTTT) {
            case HUB_TTTT_8_BITS:
                  if (hdev->descriptor.bDeviceProtocol != 0) {
                        hub->tt.think_time = 666;
                        dev_dbg(hub_dev, "TT requires at most %d "
                                    "FS bit times (%d ns)\n",
                              8, hub->tt.think_time);
                  }
                  break;
            case HUB_TTTT_16_BITS:
                  hub->tt.think_time = 666 * 2;
                  dev_dbg(hub_dev, "TT requires at most %d "
                              "FS bit times (%d ns)\n",
                        16, hub->tt.think_time);
                  break;
            case HUB_TTTT_24_BITS:
                  hub->tt.think_time = 666 * 3;
                  dev_dbg(hub_dev, "TT requires at most %d "
                              "FS bit times (%d ns)\n",
                        24, hub->tt.think_time);
                  break;
            case HUB_TTTT_32_BITS:
                  hub->tt.think_time = 666 * 4;
                  dev_dbg(hub_dev, "TT requires at most %d "
                              "FS bit times (%d ns)\n",
                        32, hub->tt.think_time);
                  break;
      }

      /* probe() zeroes hub->indicator[] */
      if (wHubCharacteristics & HUB_CHAR_PORTIND) {
            hub->has_indicators = 1;
            dev_dbg(hub_dev, "Port indicators are supported\n");
      }

      dev_dbg(hub_dev, "power on to power good time: %dms\n",
            hub->descriptor->bPwrOn2PwrGood * 2);

      /* power budgeting mostly matters with bus-powered hubs,
       * and battery-powered root hubs (may provide just 8 mA).
       */
      ret = usb_get_status(hdev, USB_RECIP_DEVICE, 0, &hubstatus);
      if (ret < 2) {
            message = "can't get hub status";
            goto fail;
      }
      le16_to_cpus(&hubstatus);
      if (hdev == hdev->bus->root_hub) {
            if (hdev->bus_mA == 0 || hdev->bus_mA >= 500)
                  hub->mA_per_port = 500;
            else {
                  hub->mA_per_port = hdev->bus_mA;
                  hub->limited_power = 1;
            }
      } else if ((hubstatus & (1 << USB_DEVICE_SELF_POWERED)) == 0) {
            dev_dbg(hub_dev, "hub controller current requirement: %dmA\n",
                  hub->descriptor->bHubContrCurrent);
            hub->limited_power = 1;
            if (hdev->maxchild > 0) {
                  int remaining = hdev->bus_mA -
                              hub->descriptor->bHubContrCurrent;

                  if (remaining < hdev->maxchild * 100)
                        dev_warn(hub_dev,
                              "insufficient power available "
                              "to use all downstream ports\n");
                  hub->mA_per_port = 100;       /* 7.2.1.1 */
            }
      } else {    /* Self-powered external hub */
            /* FIXME: What about battery-powered external hubs that
             * provide less current per port? */
            hub->mA_per_port = 500;
      }
      if (hub->mA_per_port < 500)
            dev_dbg(hub_dev, "%umA bus power budget for each child\n",
                        hub->mA_per_port);

      ret = hub_hub_status(hub, &hubstatus, &hubchange);
      if (ret < 0) {
            message = "can't get hub status";
            goto fail;
      }

      /* local power status reports aren't always correct */
      if (hdev->actconfig->desc.bmAttributes & USB_CONFIG_ATT_SELFPOWER)
            dev_dbg(hub_dev, "local power source is %s\n",
                  (hubstatus & HUB_STATUS_LOCAL_POWER)
                  ? "lost (inactive)" : "good");

      if ((wHubCharacteristics & HUB_CHAR_OCPM) == 0)
            dev_dbg(hub_dev, "%sover-current condition exists\n",
                  (hubstatus & HUB_STATUS_OVERCURRENT) ? "" : "no ");

      /* set up the interrupt endpoint
       * We use the EP's maxpacket size instead of (PORTS+1+7)/8
       * bytes as USB2.0[11.12.3] says because some hubs are known
       * to send more data (and thus cause overflow). For root hubs,
       * maxpktsize is defined in hcd.c's fake endpoint descriptors
       * to be big enough for at least USB_MAXCHILDREN ports. */
      pipe = usb_rcvintpipe(hdev, endpoint->bEndpointAddress);
      maxp = usb_maxpacket(hdev, pipe, usb_pipeout(pipe));

      if (maxp > sizeof(*hub->buffer))
            maxp = sizeof(*hub->buffer);

      hub->urb = usb_alloc_urb(0, GFP_KERNEL);
      if (!hub->urb) {
            message = "couldn't allocate interrupt urb";
            ret = -ENOMEM;
            goto fail;
      }

      usb_fill_int_urb(hub->urb, hdev, pipe, *hub->buffer, maxp, hub_irq,
            hub, endpoint->bInterval);
      hub->urb->transfer_dma = hub->buffer_dma;
      hub->urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;

      /* maybe cycle the hub leds */
      if (hub->has_indicators && blinkenlights)
            hub->indicator [0] = INDICATOR_CYCLE;

      hub_activate(hub, HUB_INIT);
      return 0;

fail:
      dev_err (hub_dev, "config failed, %s (err %d)\n",
                  message, ret);
      /* hub_disconnect() frees urb and descriptor */
      return ret;
}

static void hub_release(struct kref *kref)
{
      struct usb_hub *hub = container_of(kref, struct usb_hub, kref);

      usb_put_intf(to_usb_interface(hub->intfdev));
      kfree(hub);
}

static unsigned highspeed_hubs;

static void hub_disconnect(struct usb_interface *intf)
{
      struct usb_hub *hub = usb_get_intfdata (intf);

      /* Take the hub off the event list and don't let it be added again */
      spin_lock_irq(&hub_event_lock);
      list_del_init(&hub->event_list);
      hub->disconnected = 1;
      spin_unlock_irq(&hub_event_lock);

      /* Disconnect all children and quiesce the hub */
      hub->error = 0;
      hub_quiesce(hub, HUB_DISCONNECT);

      usb_set_intfdata (intf, NULL);

      if (hub->hdev->speed == USB_SPEED_HIGH)
            highspeed_hubs--;

      usb_free_urb(hub->urb);
      kfree(hub->descriptor);
      kfree(hub->status);
      usb_buffer_free(hub->hdev, sizeof(*hub->buffer), hub->buffer,
                  hub->buffer_dma);

      kref_put(&hub->kref, hub_release);
}

static int hub_probe(struct usb_interface *intf, const struct usb_device_id *id)
{
      struct usb_host_interface *desc;
      struct usb_endpoint_descriptor *endpoint;
      struct usb_device *hdev;
      struct usb_hub *hub;

      desc = intf->cur_altsetting;
      hdev = interface_to_usbdev(intf);

      if (hdev->level == MAX_TOPO_LEVEL) {
            dev_err(&intf->dev,
                  "Unsupported bus topology: hub nested too deep\n");
            return -E2BIG;
      }

#ifdef      CONFIG_USB_OTG_BLACKLIST_HUB
      if (hdev->parent) {
            dev_warn(&intf->dev, "ignoring external hub\n");
            return -ENODEV;
      }
#endif

      /* Some hubs have a subclass of 1, which AFAICT according to the */
      /*  specs is not defined, but it works */
      if ((desc->desc.bInterfaceSubClass != 0) &&
          (desc->desc.bInterfaceSubClass != 1)) {
descriptor_error:
            dev_err (&intf->dev, "bad descriptor, ignoring hub\n");
            return -EIO;
      }

      /* Multiple endpoints? What kind of mutant ninja-hub is this? */
      if (desc->desc.bNumEndpoints != 1)
            goto descriptor_error;

      endpoint = &desc->endpoint[0].desc;

      /* If it's not an interrupt in endpoint, we'd better punt! */
      if (!usb_endpoint_is_int_in(endpoint))
            goto descriptor_error;

      /* We found a hub */
      dev_info (&intf->dev, "USB hub found\n");

      hub = kzalloc(sizeof(*hub), GFP_KERNEL);
      if (!hub) {
            dev_dbg (&intf->dev, "couldn't kmalloc hub struct\n");
            return -ENOMEM;
      }

      kref_init(&hub->kref);
      INIT_LIST_HEAD(&hub->event_list);
      hub->intfdev = &intf->dev;
      hub->hdev = hdev;
      INIT_DELAYED_WORK(&hub->leds, led_work);
      INIT_DELAYED_WORK(&hub->init_work, NULL);
      usb_get_intf(intf);

      usb_set_intfdata (intf, hub);
      intf->needs_remote_wakeup = 1;

      if (hdev->speed == USB_SPEED_HIGH)
            highspeed_hubs++;

      if (hub_configure(hub, endpoint) >= 0)
            return 0;

      hub_disconnect (intf);
      return -ENODEV;
}

static int
hub_ioctl(struct usb_interface *intf, unsigned int code, void *user_data)
{
      struct usb_device *hdev = interface_to_usbdev (intf);

      /* assert ifno == 0 (part of hub spec) */
      switch (code) {
      case USBDEVFS_HUB_PORTINFO: {
            struct usbdevfs_hub_portinfo *info = user_data;
            int i;

            spin_lock_irq(&device_state_lock);
            if (hdev->devnum <= 0)
                  info->nports = 0;
            else {
                  info->nports = hdev->maxchild;
                  for (i = 0; i < info->nports; i++) {
                        if (hdev->children[i] == NULL)
                              info->port[i] = 0;
                        else
                              info->port[i] =
                                    hdev->children[i]->devnum;
                  }
            }
            spin_unlock_irq(&device_state_lock);

            return info->nports + 1;
            }

      default:
            return -ENOSYS;
      }
}


static void recursively_mark_NOTATTACHED(struct usb_device *udev)
{
      int i;

      for (i = 0; i < udev->maxchild; ++i) {
            if (udev->children[i])
                  recursively_mark_NOTATTACHED(udev->children[i]);
      }
      if (udev->state == USB_STATE_SUSPENDED) {
            udev->discon_suspended = 1;
            udev->active_duration -= jiffies;
      }
      udev->state = USB_STATE_NOTATTACHED;
}

/**
 * usb_set_device_state - change a device's current state (usbcore, hcds)
 * @udev: pointer to device whose state should be changed
 * @new_state: new state value to be stored
 *
 * udev->state is _not_ fully protected by the device lock.  Although
 * most transitions are made only while holding the lock, the state can
 * can change to USB_STATE_NOTATTACHED at almost any time.  This
 * is so that devices can be marked as disconnected as soon as possible,
 * without having to wait for any semaphores to be released.  As a result,
 * all changes to any device's state must be protected by the
 * device_state_lock spinlock.
 *
 * Once a device has been added to the device tree, all changes to its state
 * should be made using this routine.  The state should _not_ be set directly.
 *
 * If udev->state is already USB_STATE_NOTATTACHED then no change is made.
 * Otherwise udev->state is set to new_state, and if new_state is
 * USB_STATE_NOTATTACHED then all of udev's descendants' states are also set
 * to USB_STATE_NOTATTACHED.
 */
void usb_set_device_state(struct usb_device *udev,
            enum usb_device_state new_state)
{
      unsigned long flags;

      spin_lock_irqsave(&device_state_lock, flags);
      if (udev->state == USB_STATE_NOTATTACHED)
            ;     /* do nothing */
      else if (new_state != USB_STATE_NOTATTACHED) {

            /* root hub wakeup capabilities are managed out-of-band
             * and may involve silicon errata ... ignore them here.
             */
            if (udev->parent) {
                  if (udev->state == USB_STATE_SUSPENDED
                              || new_state == USB_STATE_SUSPENDED)
                        ;     /* No change to wakeup settings */
                  else if (new_state == USB_STATE_CONFIGURED)
                        device_init_wakeup(&udev->dev,
                              (udev->actconfig->desc.bmAttributes
                               & USB_CONFIG_ATT_WAKEUP));
                  else
                        device_init_wakeup(&udev->dev, 0);
            }
            if (udev->state == USB_STATE_SUSPENDED &&
                  new_state != USB_STATE_SUSPENDED)
                  udev->active_duration -= jiffies;
            else if (new_state == USB_STATE_SUSPENDED &&
                        udev->state != USB_STATE_SUSPENDED)
                  udev->active_duration += jiffies;
            udev->state = new_state;
      } else
            recursively_mark_NOTATTACHED(udev);
      spin_unlock_irqrestore(&device_state_lock, flags);
}
EXPORT_SYMBOL_GPL(usb_set_device_state);

/*
 * WUSB devices are simple: they have no hubs behind, so the mapping
 * device <-> virtual port number becomes 1:1. Why? to simplify the
 * life of the device connection logic in
 * drivers/usb/wusbcore/devconnect.c. When we do the initial secret
 * handshake we need to assign a temporary address in the unauthorized
 * space. For simplicity we use the first virtual port number found to
 * be free [drivers/usb/wusbcore/devconnect.c:wusbhc_devconnect_ack()]
 * and that becomes it's address [X < 128] or its unauthorized address
 * [X | 0x80].
 *
 * We add 1 as an offset to the one-based USB-stack port number
 * (zero-based wusb virtual port index) for two reasons: (a) dev addr
 * 0 is reserved by USB for default address; (b) Linux's USB stack
 * uses always #1 for the root hub of the controller. So USB stack's
 * port #1, which is wusb virtual-port #0 has address #2.
 *
 * Devices connected under xHCI are not as simple.  The host controller
 * supports virtualization, so the hardware assigns device addresses and
 * the HCD must setup data structures before issuing a set address
 * command to the hardware.
 */
static void choose_address(struct usb_device *udev)
{
      int         devnum;
      struct usb_bus    *bus = udev->bus;

      /* If khubd ever becomes multithreaded, this will need a lock */
      if (udev->wusb) {
            devnum = udev->portnum + 1;
            BUG_ON(test_bit(devnum, bus->devmap.devicemap));
      } else {
            /* Try to allocate the next devnum beginning at
             * bus->devnum_next. */
            devnum = find_next_zero_bit(bus->devmap.devicemap, 128,
                                  bus->devnum_next);
            if (devnum >= 128)
                  devnum = find_next_zero_bit(bus->devmap.devicemap,
                                        128, 1);
            bus->devnum_next = ( devnum >= 127 ? 1 : devnum + 1);
      }
      if (devnum < 128) {
            set_bit(devnum, bus->devmap.devicemap);
            udev->devnum = devnum;
      }
}

static void release_address(struct usb_device *udev)
{
      if (udev->devnum > 0) {
            clear_bit(udev->devnum, udev->bus->devmap.devicemap);
            udev->devnum = -1;
      }
}

static void update_address(struct usb_device *udev, int devnum)
{
      /* The address for a WUSB device is managed by wusbcore. */
      if (!udev->wusb)
            udev->devnum = devnum;
}

#ifdef      CONFIG_USB_SUSPEND

static void usb_stop_pm(struct usb_device *udev)
{
      /* Synchronize with the ksuspend thread to prevent any more
       * autosuspend requests from being submitted, and decrement
       * the parent's count of unsuspended children.
       */
      usb_pm_lock(udev);
      if (udev->parent && !udev->discon_suspended)
            usb_autosuspend_device(udev->parent);
      usb_pm_unlock(udev);

      /* Stop any autosuspend or autoresume requests already submitted */
      cancel_delayed_work_sync(&udev->autosuspend);
      cancel_work_sync(&udev->autoresume);
}

#else

static inline void usb_stop_pm(struct usb_device *udev)
{ }

#endif

/**
 * usb_disconnect - disconnect a device (usbcore-internal)
 * @pdev: pointer to device being disconnected
 * Context: !in_interrupt ()
 *
 * Something got disconnected. Get rid of it and all of its children.
 *
 * If *pdev is a normal device then the parent hub must already be locked.
 * If *pdev is a root hub then this routine will acquire the
 * usb_bus_list_lock on behalf of the caller.
 *
 * Only hub drivers (including virtual root hub drivers for host
 * controllers) should ever call this.
 *
 * This call is synchronous, and may not be used in an interrupt context.
 */
void usb_disconnect(struct usb_device **pdev)
{
      struct usb_device *udev = *pdev;
      int               i;

      if (!udev) {
            pr_debug ("%s nodev\n", __func__);
            return;
      }

      /* mark the device as inactive, so any further urb submissions for
       * this device (and any of its children) will fail immediately.
       * this quiesces everyting except pending urbs.
       */
      usb_set_device_state(udev, USB_STATE_NOTATTACHED);
      dev_info (&udev->dev, "USB disconnect, address %d\n", udev->devnum);

      usb_lock_device(udev);

      /* Free up all the children before we remove this device */
      for (i = 0; i < USB_MAXCHILDREN; i++) {
            if (udev->children[i])
                  usb_disconnect(&udev->children[i]);
      }

      /* deallocate hcd/hardware state ... nuking all pending urbs and
       * cleaning up all state associated with the current configuration
       * so that the hardware is now fully quiesced.
       */
      dev_dbg (&udev->dev, "unregistering device\n");
      usb_disable_device(udev, 0);
      usb_hcd_synchronize_unlinks(udev);

      usb_remove_ep_devs(&udev->ep0);
      usb_unlock_device(udev);

      /* Unregister the device.  The device driver is responsible
       * for de-configuring the device and invoking the remove-device
       * notifier chain (used by usbfs and possibly others).
       */
      device_del(&udev->dev);

      /* Free the device number and delete the parent's children[]
       * (or root_hub) pointer.
       */
      release_address(udev);

      /* Avoid races with recursively_mark_NOTATTACHED() */
      spin_lock_irq(&device_state_lock);
      *pdev = NULL;
      spin_unlock_irq(&device_state_lock);

      usb_stop_pm(udev);

      put_device(&udev->dev);
}

#ifdef CONFIG_USB_ANNOUNCE_NEW_DEVICES
static void show_string(struct usb_device *udev, char *id, char *string)
{
      if (!string)
            return;
      dev_printk(KERN_INFO, &udev->dev, "%s: %s\n", id, string);
}

static void announce_device(struct usb_device *udev)
{
      dev_info(&udev->dev, "New USB device found, idVendor=%04x, idProduct=%04x\n",
            le16_to_cpu(udev->descriptor.idVendor),
            le16_to_cpu(udev->descriptor.idProduct));
      dev_info(&udev->dev,
            "New USB device strings: Mfr=%d, Product=%d, SerialNumber=%d\n",
            udev->descriptor.iManufacturer,
            udev->descriptor.iProduct,
            udev->descriptor.iSerialNumber);
      show_string(udev, "Product", udev->product);
      show_string(udev, "Manufacturer", udev->manufacturer);
      show_string(udev, "SerialNumber", udev->serial);
}
#else
static inline void announce_device(struct usb_device *udev) { }
#endif

#ifdef      CONFIG_USB_OTG
#include "otg_whitelist.h"
#endif

/**
 * usb_configure_device_otg - FIXME (usbcore-internal)
 * @udev: newly addressed device (in ADDRESS state)
 *
 * Do configuration for On-The-Go devices
 */
static int usb_configure_device_otg(struct usb_device *udev)
{
      int err = 0;

#ifdef      CONFIG_USB_OTG
      /*
       * OTG-aware devices on OTG-capable root hubs may be able to use SRP,
       * to wake us after we've powered off VBUS; and HNP, switching roles
       * "host" to "peripheral".  The OTG descriptor helps figure this out.
       */
      if (!udev->bus->is_b_host
                  && udev->config
                  && udev->parent == udev->bus->root_hub) {
            struct usb_otg_descriptor     *desc = 0;
            struct usb_bus                *bus = udev->bus;

            /* descriptor may appear anywhere in config */
            if (__usb_get_extra_descriptor (udev->rawdescriptors[0],
                              le16_to_cpu(udev->config[0].desc.wTotalLength),
                              USB_DT_OTG, (void **) &desc) == 0) {
                  if (desc->bmAttributes & USB_OTG_HNP) {
                        unsigned          port1 = udev->portnum;

                        dev_info(&udev->dev,
                              "Dual-Role OTG device on %sHNP port\n",
                              (port1 == bus->otg_port)
                                    ? "" : "non-");

                        /* enable HNP before suspend, it's simpler */
                        if (port1 == bus->otg_port)
                              bus->b_hnp_enable = 1;
                        err = usb_control_msg(udev,
                              usb_sndctrlpipe(udev, 0),
                              USB_REQ_SET_FEATURE, 0,
                              bus->b_hnp_enable
                                    ? USB_DEVICE_B_HNP_ENABLE
                                    : USB_DEVICE_A_ALT_HNP_SUPPORT,
                              0, NULL, 0, USB_CTRL_SET_TIMEOUT);
                        if (err < 0) {
                              /* OTG MESSAGE: report errors here,
                               * customize to match your product.
                               */
                              dev_info(&udev->dev,
                                    "can't set HNP mode: %d\n",
                                    err);
                              bus->b_hnp_enable = 0;
                        }
                  }
            }
      }

      if (!is_targeted(udev)) {

            /* Maybe it can talk to us, though we can't talk to it.
             * (Includes HNP test device.)
             */
            if (udev->bus->b_hnp_enable || udev->bus->is_b_host) {
                  err = usb_port_suspend(udev, PMSG_SUSPEND);
                  if (err < 0)
                        dev_dbg(&udev->dev, "HNP fail, %d\n", err);
            }
            err = -ENOTSUPP;
            goto fail;
      }
fail:
#endif
      return err;
}


/**
 * usb_configure_device - Detect and probe device intfs/otg (usbcore-internal)
 * @udev: newly addressed device (in ADDRESS state)
 *
 * This is only called by usb_new_device() and usb_authorize_device()
 * and FIXME -- all comments that apply to them apply here wrt to
 * environment.
 *
 * If the device is WUSB and not authorized, we don't attempt to read
 * the string descriptors, as they will be errored out by the device
 * until it has been authorized.
 */
static int usb_configure_device(struct usb_device *udev)
{
      int err;

      if (udev->config == NULL) {
            err = usb_get_configuration(udev);
            if (err < 0) {
                  dev_err(&udev->dev, "can't read configurations, error %d\n",
                        err);
                  goto fail;
            }
      }
      if (udev->wusb == 1 && udev->authorized == 0) {
            udev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL);
            udev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL);
            udev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL);
      }
      else {
            /* read the standard strings and cache them if present */
            udev->product = usb_cache_string(udev, udev->descriptor.iProduct);
            udev->manufacturer = usb_cache_string(udev,
                                          udev->descriptor.iManufacturer);
            udev->serial = usb_cache_string(udev, udev->descriptor.iSerialNumber);
      }
      err = usb_configure_device_otg(udev);
fail:
      return err;
}


/**
 * usb_new_device - perform initial device setup (usbcore-internal)
 * @udev: newly addressed device (in ADDRESS state)
 *
 * This is called with devices which have been enumerated, but not yet
 * configured.  The device descriptor is available, but not descriptors
 * for any device configuration.  The caller must have locked either
 * the parent hub (if udev is a normal device) or else the
 * usb_bus_list_lock (if udev is a root hub).  The parent's pointer to
 * udev has already been installed, but udev is not yet visible through
 * sysfs or other filesystem code.
 *
 * It will return if the device is configured properly or not.  Zero if
 * the interface was registered with the driver core; else a negative
 * errno value.
 *
 * This call is synchronous, and may not be used in an interrupt context.
 *
 * Only the hub driver or root-hub registrar should ever call this.
 */
int usb_new_device(struct usb_device *udev)
{
      int err;

      /* Increment the parent's count of unsuspended children */
      if (udev->parent)
            usb_autoresume_device(udev->parent);

      usb_detect_quirks(udev);            /* Determine quirks */
      err = usb_configure_device(udev);   /* detect & probe dev/intfs */
      if (err < 0)
            goto fail;
      dev_dbg(&udev->dev, "udev %d, busnum %d, minor = %d\n",
                  udev->devnum, udev->bus->busnum,
                  (((udev->bus->busnum-1) * 128) + (udev->devnum-1)));
      /* export the usbdev device-node for libusb */
      udev->dev.devt = MKDEV(USB_DEVICE_MAJOR,
                  (((udev->bus->busnum-1) * 128) + (udev->devnum-1)));

      /* Tell the world! */
      announce_device(udev);

      /* Register the device.  The device driver is responsible
       * for configuring the device and invoking the add-device
       * notifier chain (used by usbfs and possibly others).
       */
      err = device_add(&udev->dev);
      if (err) {
            dev_err(&udev->dev, "can't device_add, error %d\n", err);
            goto fail;
      }

      (void) usb_create_ep_devs(&udev->dev, &udev->ep0, udev);
      return err;

fail:
      usb_set_device_state(udev, USB_STATE_NOTATTACHED);
      usb_stop_pm(udev);
      return err;
}


/**
 * usb_deauthorize_device - deauthorize a device (usbcore-internal)
 * @usb_dev: USB device
 *
 * Move the USB device to a very basic state where interfaces are disabled
 * and the device is in fact unconfigured and unusable.
 *
 * We share a lock (that we have) with device_del(), so we need to
 * defer its call.
 */
int usb_deauthorize_device(struct usb_device *usb_dev)
{
      unsigned cnt;
      usb_lock_device(usb_dev);
      if (usb_dev->authorized == 0)
            goto out_unauthorized;
      usb_dev->authorized = 0;
      usb_set_configuration(usb_dev, -1);
      usb_dev->product = kstrdup("n/a (unauthorized)", GFP_KERNEL);
      usb_dev->manufacturer = kstrdup("n/a (unauthorized)", GFP_KERNEL);
      usb_dev->serial = kstrdup("n/a (unauthorized)", GFP_KERNEL);
      kfree(usb_dev->config);
      usb_dev->config = NULL;
      for (cnt = 0; cnt < usb_dev->descriptor.bNumConfigurations; cnt++)
            kfree(usb_dev->rawdescriptors[cnt]);
      usb_dev->descriptor.bNumConfigurations = 0;
      kfree(usb_dev->rawdescriptors);
out_unauthorized:
      usb_unlock_device(usb_dev);
      return 0;
}


int usb_authorize_device(struct usb_device *usb_dev)
{
      int result = 0, c;
      usb_lock_device(usb_dev);
      if (usb_dev->authorized == 1)
            goto out_authorized;
      kfree(usb_dev->product);
      usb_dev->product = NULL;
      kfree(usb_dev->manufacturer);
      usb_dev->manufacturer = NULL;
      kfree(usb_dev->serial);
      usb_dev->serial = NULL;
      result = usb_autoresume_device(usb_dev);
      if (result < 0) {
            dev_err(&usb_dev->dev,
                  "can't autoresume for authorization: %d\n", result);
            goto error_autoresume;
      }
      result = usb_get_device_descriptor(usb_dev, sizeof(usb_dev->descriptor));
      if (result < 0) {
            dev_err(&usb_dev->dev, "can't re-read device descriptor for "
                  "authorization: %d\n", result);
            goto error_device_descriptor;
      }
      usb_dev->authorized = 1;
      result = usb_configure_device(usb_dev);
      if (result < 0)
            goto error_configure;
      /* Choose and set the configuration.  This registers the interfaces
       * with the driver core and lets interface drivers bind to them.
       */
      c = usb_choose_configuration(usb_dev);
      if (c >= 0) {
            result = usb_set_configuration(usb_dev, c);
            if (result) {
                  dev_err(&usb_dev->dev,
                        "can't set config #%d, error %d\n", c, result);
                  /* This need not be fatal.  The user can try to
                   * set other configurations. */
            }
      }
      dev_info(&usb_dev->dev, "authorized to connect\n");
error_configure:
error_device_descriptor:
error_autoresume:
out_authorized:
      usb_unlock_device(usb_dev);   // complements locktree
      return result;
}


/* Returns 1 if @hub is a WUSB root hub, 0 otherwise */
static unsigned hub_is_wusb(struct usb_hub *hub)
{
      struct usb_hcd *hcd;
      if (hub->hdev->parent != NULL)  /* not a root hub? */
            return 0;
      hcd = container_of(hub->hdev->bus, struct usb_hcd, self);
      return hcd->wireless;
}


#define PORT_RESET_TRIES      5
#define SET_ADDRESS_TRIES     2
#define GET_DESCRIPTOR_TRIES  2
#define SET_CONFIG_TRIES      (2 * (use_both_schemes + 1))
#define USE_NEW_SCHEME(i)     ((i) / 2 == old_scheme_first)

#define HUB_ROOT_RESET_TIME   50    /* times are in msec */
#define HUB_SHORT_RESET_TIME  10
#define HUB_LONG_RESET_TIME   200
#define HUB_RESET_TIMEOUT     500

static int hub_port_wait_reset(struct usb_hub *hub, int port1,
                        struct usb_device *udev, unsigned int delay)
{
      int delay_time, ret;
      u16 portstatus;
      u16 portchange;

      for (delay_time = 0;
                  delay_time < HUB_RESET_TIMEOUT;
                  delay_time += delay) {
            /* wait to give the device a chance to reset */
            msleep(delay);

            /* read and decode port status */
            ret = hub_port_status(hub, port1, &portstatus, &portchange);
            if (ret < 0)
                  return ret;

            /* Device went away? */
            if (!(portstatus & USB_PORT_STAT_CONNECTION))
                  return -ENOTCONN;

            /* bomb out completely if the connection bounced */
            if ((portchange & USB_PORT_STAT_C_CONNECTION))
                  return -ENOTCONN;

            /* if we`ve finished resetting, then break out of the loop */
            if (!(portstatus & USB_PORT_STAT_RESET) &&
                (portstatus & USB_PORT_STAT_ENABLE)) {
                  if (hub_is_wusb(hub))
                        udev->speed = USB_SPEED_VARIABLE;
                  else if (portstatus & USB_PORT_STAT_HIGH_SPEED)
                        udev->speed = USB_SPEED_HIGH;
                  else if (portstatus & USB_PORT_STAT_LOW_SPEED)
                        udev->speed = USB_SPEED_LOW;
                  else
                        udev->speed = USB_SPEED_FULL;
                  return 0;
            }

            /* switch to the long delay after two short delay failures */
            if (delay_time >= 2 * HUB_SHORT_RESET_TIME)
                  delay = HUB_LONG_RESET_TIME;

            dev_dbg (hub->intfdev,
                  "port %d not reset yet, waiting %dms\n",
                  port1, delay);
      }

      return -EBUSY;
}

static int hub_port_reset(struct usb_hub *hub, int port1,
                        struct usb_device *udev, unsigned int delay)
{
      int i, status;

      /* Block EHCI CF initialization during the port reset.
       * Some companion controllers don't like it when they mix.
       */
      down_read(&ehci_cf_port_reset_rwsem);

      /* Reset the port */
      for (i = 0; i < PORT_RESET_TRIES; i++) {
            status = set_port_feature(hub->hdev,
                        port1, USB_PORT_FEAT_RESET);
            if (status)
                  dev_err(hub->intfdev,
                              "cannot reset port %d (err = %d)\n",
                              port1, status);
            else {
                  status = hub_port_wait_reset(hub, port1, udev, delay);
                  if (status && status != -ENOTCONN)
                        dev_dbg(hub->intfdev,
                                    "port_wait_reset: err = %d\n",
                                    status);
            }

            /* return on disconnect or reset */
            switch (status) {
            case 0:
                  /* TRSTRCY = 10 ms; plus some extra */
                  msleep(10 + 40);
                  update_address(udev, 0);
                  /* FALL THROUGH */
            case -ENOTCONN:
            case -ENODEV:
                  clear_port_feature(hub->hdev,
                        port1, USB_PORT_FEAT_C_RESET);
                  /* FIXME need disconnect() for NOTATTACHED device */
                  usb_set_device_state(udev, status
                              ? USB_STATE_NOTATTACHED
                              : USB_STATE_DEFAULT);
                  goto done;
            }

            dev_dbg (hub->intfdev,
                  "port %d not enabled, trying reset again...\n",
                  port1);
            delay = HUB_LONG_RESET_TIME;
      }

      dev_err (hub->intfdev,
            "Cannot enable port %i.  Maybe the USB cable is bad?\n",
            port1);

 done:
      up_read(&ehci_cf_port_reset_rwsem);
      return status;
}

#ifdef      CONFIG_PM

#define MASK_BITS (USB_PORT_STAT_POWER | USB_PORT_STAT_CONNECTION | \
                        USB_PORT_STAT_SUSPEND)
#define WANT_BITS (USB_PORT_STAT_POWER | USB_PORT_STAT_CONNECTION)

/* Determine whether the device on a port is ready for a normal resume,
 * is ready for a reset-resume, or should be disconnected.
 */
static int check_port_resume_type(struct usb_device *udev,
            struct usb_hub *hub, int port1,
            int status, unsigned portchange, unsigned portstatus)
{
      /* Is the device still present? */
      if (status || (portstatus & MASK_BITS) != WANT_BITS) {
            if (status >= 0)
                  status = -ENODEV;
      }

      /* Can't do a normal resume if the port isn't enabled,
       * so try a reset-resume instead.
       */
      else if (!(portstatus & USB_PORT_STAT_ENABLE) && !udev->reset_resume) {
            if (udev->persist_enabled)
                  udev->reset_resume = 1;
            else
                  status = -ENODEV;
      }

      if (status) {
            dev_dbg(hub->intfdev,
                        "port %d status %04x.%04x after resume, %d\n",
                        port1, portchange, portstatus, status);
      } else if (udev->reset_resume) {

            /* Late port handoff can set status-change bits */
            if (portchange & USB_PORT_STAT_C_CONNECTION)
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_CONNECTION);
            if (portchange & USB_PORT_STAT_C_ENABLE)
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_ENABLE);
      }

      return status;
}

#ifdef      CONFIG_USB_SUSPEND

/*
 * usb_port_suspend - suspend a usb device's upstream port
 * @udev: device that's no longer in active use, not a root hub
 * Context: must be able to sleep; device not locked; pm locks held
 *
 * Suspends a USB device that isn't in active use, conserving power.
 * Devices may wake out of a suspend, if anything important happens,
 * using the remote wakeup mechanism.  They may also be taken out of
 * suspend by the host, using usb_port_resume().  It's also routine
 * to disconnect devices while they are suspended.
 *
 * This only affects the USB hardware for a device; its interfaces
 * (and, for hubs, child devices) must already have been suspended.
 *
 * Selective port suspend reduces power; most suspended devices draw
 * less than 500 uA.  It's also used in OTG, along with remote wakeup.
 * All devices below the suspended port are also suspended.
 *
 * Devices leave suspend state when the host wakes them up.  Some devices
 * also support "remote wakeup", where the device can activate the USB
 * tree above them to deliver data, such as a keypress or packet.  In
 * some cases, this wakes the USB host.
 *
 * Suspending OTG devices may trigger HNP, if that's been enabled
 * between a pair of dual-role devices.  That will change roles, such
 * as from A-Host to A-Peripheral or from B-Host back to B-Peripheral.
 *
 * Devices on USB hub ports have only one "suspend" state, corresponding
 * to ACPI D2, "may cause the device to lose some context".
 * State transitions include:
 *
 *   - suspend, resume ... when the VBUS power link stays live
 *   - suspend, disconnect ... VBUS lost
 *
 * Once VBUS drop breaks the circuit, the port it's using has to go through
 * normal re-enumeration procedures, starting with enabling VBUS power.
 * Other than re-initializing the hub (plug/unplug, except for root hubs),
 * Linux (2.6) currently has NO mechanisms to initiate that:  no khubd
 * timer, no SRP, no requests through sysfs.
 *
 * If CONFIG_USB_SUSPEND isn't enabled, devices only really suspend when
 * the root hub for their bus goes into global suspend ... so we don't
 * (falsely) update the device power state to say it suspended.
 *
 * Returns 0 on success, else negative errno.
 */
int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
{
      struct usb_hub    *hub = hdev_to_hub(udev->parent);
      int         port1 = udev->portnum;
      int         status;

      // dev_dbg(hub->intfdev, "suspend port %d\n", port1);

      /* enable remote wakeup when appropriate; this lets the device
       * wake up the upstream hub (including maybe the root hub).
       *
       * NOTE:  OTG devices may issue remote wakeup (or SRP) even when
       * we don't explicitly enable it here.
       */
      if (udev->do_remote_wakeup) {
            status = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
                        USB_REQ_SET_FEATURE, USB_RECIP_DEVICE,
                        USB_DEVICE_REMOTE_WAKEUP, 0,
                        NULL, 0,
                        USB_CTRL_SET_TIMEOUT);
            if (status)
                  dev_dbg(&udev->dev, "won't remote wakeup, status %d\n",
                              status);
      }

      /* see 7.1.7.6 */
      status = set_port_feature(hub->hdev, port1, USB_PORT_FEAT_SUSPEND);
      if (status) {
            dev_dbg(hub->intfdev, "can't suspend port %d, status %d\n",
                        port1, status);
            /* paranoia:  "should not happen" */
            (void) usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
                        USB_REQ_CLEAR_FEATURE, USB_RECIP_DEVICE,
                        USB_DEVICE_REMOTE_WAKEUP, 0,
                        NULL, 0,
                        USB_CTRL_SET_TIMEOUT);
      } else {
            /* device has up to 10 msec to fully suspend */
            dev_dbg(&udev->dev, "usb %ssuspend\n",
                        (msg.event & PM_EVENT_AUTO ? "auto-" : ""));
            usb_set_device_state(udev, USB_STATE_SUSPENDED);
            msleep(10);
      }
      return status;
}

/*
 * If the USB "suspend" state is in use (rather than "global suspend"),
 * many devices will be individually taken out of suspend state using
 * special "resume" signaling.  This routine kicks in shortly after
 * hardware resume signaling is finished, either because of selective
 * resume (by host) or remote wakeup (by device) ... now see what changed
 * in the tree that's rooted at this device.
 *
 * If @udev->reset_resume is set then the device is reset before the
 * status check is done.
 */
static int finish_port_resume(struct usb_device *udev)
{
      int   status = 0;
      u16   devstatus;

      /* caller owns the udev device lock */
      dev_dbg(&udev->dev, "%s\n",
            udev->reset_resume ? "finish reset-resume" : "finish resume");

      /* usb ch9 identifies four variants of SUSPENDED, based on what
       * state the device resumes to.  Linux currently won't see the
       * first two on the host side; they'd be inside hub_port_init()
       * during many timeouts, but khubd can't suspend until later.
       */
      usb_set_device_state(udev, udev->actconfig
                  ? USB_STATE_CONFIGURED
                  : USB_STATE_ADDRESS);

      /* 10.5.4.5 says not to reset a suspended port if the attached
       * device is enabled for remote wakeup.  Hence the reset
       * operation is carried out here, after the port has been
       * resumed.
       */
      if (udev->reset_resume)
 retry_reset_resume:
            status = usb_reset_and_verify_device(udev);

      /* 10.5.4.5 says be sure devices in the tree are still there.
       * For now let's assume the device didn't go crazy on resume,
       * and device drivers will know about any resume quirks.
       */
      if (status == 0) {
            devstatus = 0;
            status = usb_get_status(udev, USB_RECIP_DEVICE, 0, &devstatus);
            if (status >= 0)
                  status = (status > 0 ? 0 : -ENODEV);

            /* If a normal resume failed, try doing a reset-resume */
            if (status && !udev->reset_resume && udev->persist_enabled) {
                  dev_dbg(&udev->dev, "retry with reset-resume\n");
                  udev->reset_resume = 1;
                  goto retry_reset_resume;
            }
      }

      if (status) {
            dev_dbg(&udev->dev, "gone after usb resume? status %d\n",
                        status);
      } else if (udev->actconfig) {
            le16_to_cpus(&devstatus);
            if (devstatus & (1 << USB_DEVICE_REMOTE_WAKEUP)) {
                  status = usb_control_msg(udev,
                              usb_sndctrlpipe(udev, 0),
                              USB_REQ_CLEAR_FEATURE,
                                    USB_RECIP_DEVICE,
                              USB_DEVICE_REMOTE_WAKEUP, 0,
                              NULL, 0,
                              USB_CTRL_SET_TIMEOUT);
                  if (status)
                        dev_dbg(&udev->dev,
                              "disable remote wakeup, status %d\n",
                              status);
            }
            status = 0;
      }
      return status;
}

/*
 * usb_port_resume - re-activate a suspended usb device's upstream port
 * @udev: device to re-activate, not a root hub
 * Context: must be able to sleep; device not locked; pm locks held
 *
 * This will re-activate the suspended device, increasing power usage
 * while letting drivers communicate again with its endpoints.
 * USB resume explicitly guarantees that the power session between
 * the host and the device is the same as it was when the device
 * suspended.
 *
 * If @udev->reset_resume is set then this routine won't check that the
 * port is still enabled.  Furthermore, finish_port_resume() above will
 * reset @udev.  The end result is that a broken power session can be
 * recovered and @udev will appear to persist across a loss of VBUS power.
 *
 * For example, if a host controller doesn't maintain VBUS suspend current
 * during a system sleep or is reset when the system wakes up, all the USB
 * power sessions below it will be broken.  This is especially troublesome
 * for mass-storage devices containing mounted filesystems, since the
 * device will appear to have disconnected and all the memory mappings
 * to it will be lost.  Using the USB_PERSIST facility, the device can be
 * made to appear as if it had not disconnected.
 *
 * This facility can be dangerous.  Although usb_reset_and_verify_device() makes
 * every effort to insure that the same device is present after the
 * reset as before, it cannot provide a 100% guarantee.  Furthermore it's
 * quite possible for a device to remain unaltered but its media to be
 * changed.  If the user replaces a flash memory card while the system is
 * asleep, he will have only himself to blame when the filesystem on the
 * new card is corrupted and the system crashes.
 *
 * Returns 0 on success, else negative errno.
 */
int usb_port_resume(struct usb_device *udev, pm_message_t msg)
{
      struct usb_hub    *hub = hdev_to_hub(udev->parent);
      int         port1 = udev->portnum;
      int         status;
      u16         portchange, portstatus;

      /* Skip the initial Clear-Suspend step for a remote wakeup */
      status = hub_port_status(hub, port1, &portstatus, &portchange);
      if (status == 0 && !(portstatus & USB_PORT_STAT_SUSPEND))
            goto SuspendCleared;

      // dev_dbg(hub->intfdev, "resume port %d\n", port1);

      set_bit(port1, hub->busy_bits);

      /* see 7.1.7.7; affects power usage, but not budgeting */
      status = clear_port_feature(hub->hdev,
                  port1, USB_PORT_FEAT_SUSPEND);
      if (status) {
            dev_dbg(hub->intfdev, "can't resume port %d, status %d\n",
                        port1, status);
      } else {
            /* drive resume for at least 20 msec */
            dev_dbg(&udev->dev, "usb %sresume\n",
                        (msg.event & PM_EVENT_AUTO ? "auto-" : ""));
            msleep(25);

            /* Virtual root hubs can trigger on GET_PORT_STATUS to
             * stop resume signaling.  Then finish the resume
             * sequence.
             */
            status = hub_port_status(hub, port1, &portstatus, &portchange);

            /* TRSMRCY = 10 msec */
            msleep(10);
      }

 SuspendCleared:
      if (status == 0) {
            if (portchange & USB_PORT_STAT_C_SUSPEND)
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_SUSPEND);
      }

      clear_bit(port1, hub->busy_bits);

      status = check_port_resume_type(udev,
                  hub, port1, status, portchange, portstatus);
      if (status == 0)
            status = finish_port_resume(udev);
      if (status < 0) {
            dev_dbg(&udev->dev, "can't resume, status %d\n", status);
            hub_port_logical_disconnect(hub, port1);
      }
      return status;
}

/* caller has locked udev */
static int remote_wakeup(struct usb_device *udev)
{
      int   status = 0;

      if (udev->state == USB_STATE_SUSPENDED) {
            dev_dbg(&udev->dev, "usb %sresume\n", "wakeup-");
            usb_mark_last_busy(udev);
            status = usb_external_resume_device(udev, PMSG_REMOTE_RESUME);
      }
      return status;
}

#else /* CONFIG_USB_SUSPEND */

/* When CONFIG_USB_SUSPEND isn't set, we never suspend or resume any ports. */

int usb_port_suspend(struct usb_device *udev, pm_message_t msg)
{
      return 0;
}

/* However we may need to do a reset-resume */

int usb_port_resume(struct usb_device *udev, pm_message_t msg)
{
      struct usb_hub    *hub = hdev_to_hub(udev->parent);
      int         port1 = udev->portnum;
      int         status;
      u16         portchange, portstatus;

      status = hub_port_status(hub, port1, &portstatus, &portchange);
      status = check_port_resume_type(udev,
                  hub, port1, status, portchange, portstatus);

      if (status) {
            dev_dbg(&udev->dev, "can't resume, status %d\n", status);
            hub_port_logical_disconnect(hub, port1);
      } else if (udev->reset_resume) {
            dev_dbg(&udev->dev, "reset-resume\n");
            status = usb_reset_and_verify_device(udev);
      }
      return status;
}

static inline int remote_wakeup(struct usb_device *udev)
{
      return 0;
}

#endif

static int hub_suspend(struct usb_interface *intf, pm_message_t msg)
{
      struct usb_hub          *hub = usb_get_intfdata (intf);
      struct usb_device *hdev = hub->hdev;
      unsigned          port1;

      /* fail if children aren't already suspended */
      for (port1 = 1; port1 <= hdev->maxchild; port1++) {
            struct usb_device *udev;

            udev = hdev->children [port1-1];
            if (udev && udev->can_submit) {
                  if (!(msg.event & PM_EVENT_AUTO))
                        dev_dbg(&intf->dev, "port %d nyet suspended\n",
                                    port1);
                  return -EBUSY;
            }
      }

      dev_dbg(&intf->dev, "%s\n", __func__);

      /* stop khubd and related activity */
      hub_quiesce(hub, HUB_SUSPEND);
      return 0;
}

static int hub_resume(struct usb_interface *intf)
{
      struct usb_hub *hub = usb_get_intfdata(intf);

      dev_dbg(&intf->dev, "%s\n", __func__);
      hub_activate(hub, HUB_RESUME);
      return 0;
}

static int hub_reset_resume(struct usb_interface *intf)
{
      struct usb_hub *hub = usb_get_intfdata(intf);

      dev_dbg(&intf->dev, "%s\n", __func__);
      hub_activate(hub, HUB_RESET_RESUME);
      return 0;
}

/**
 * usb_root_hub_lost_power - called by HCD if the root hub lost Vbus power
 * @rhdev: struct usb_device for the root hub
 *
 * The USB host controller driver calls this function when its root hub
 * is resumed and Vbus power has been interrupted or the controller
 * has been reset.  The routine marks @rhdev as having lost power.
 * When the hub driver is resumed it will take notice and carry out
 * power-session recovery for all the "USB-PERSIST"-enabled child devices;
 * the others will be disconnected.
 */
void usb_root_hub_lost_power(struct usb_device *rhdev)
{
      dev_warn(&rhdev->dev, "root hub lost power or was reset\n");
      rhdev->reset_resume = 1;
}
EXPORT_SYMBOL_GPL(usb_root_hub_lost_power);

#else /* CONFIG_PM */

static inline int remote_wakeup(struct usb_device *udev)
{
      return 0;
}

#define hub_suspend           NULL
#define hub_resume            NULL
#define hub_reset_resume      NULL
#endif


/* USB 2.0 spec, 7.1.7.3 / fig 7-29:
 *
 * Between connect detection and reset signaling there must be a delay
 * of 100ms at least for debounce and power-settling.  The corresponding
 * timer shall restart whenever the downstream port detects a disconnect.
 * 
 * Apparently there are some bluetooth and irda-dongles and a number of
 * low-speed devices for which this debounce period may last over a second.
 * Not covered by the spec - but easy to deal with.
 *
 * This implementation uses a 1500ms total debounce timeout; if the
 * connection isn't stable by then it returns -ETIMEDOUT.  It checks
 * every 25ms for transient disconnects.  When the port status has been
 * unchanged for 100ms it returns the port status.
 */
static int hub_port_debounce(struct usb_hub *hub, int port1)
{
      int ret;
      int total_time, stable_time = 0;
      u16 portchange, portstatus;
      unsigned connection = 0xffff;

      for (total_time = 0; ; total_time += HUB_DEBOUNCE_STEP) {
            ret = hub_port_status(hub, port1, &portstatus, &portchange);
            if (ret < 0)
                  return ret;

            if (!(portchange & USB_PORT_STAT_C_CONNECTION) &&
                 (portstatus & USB_PORT_STAT_CONNECTION) == connection) {
                  stable_time += HUB_DEBOUNCE_STEP;
                  if (stable_time >= HUB_DEBOUNCE_STABLE)
                        break;
            } else {
                  stable_time = 0;
                  connection = portstatus & USB_PORT_STAT_CONNECTION;
            }

            if (portchange & USB_PORT_STAT_C_CONNECTION) {
                  clear_port_feature(hub->hdev, port1,
                              USB_PORT_FEAT_C_CONNECTION);
            }

            if (total_time >= HUB_DEBOUNCE_TIMEOUT)
                  break;
            msleep(HUB_DEBOUNCE_STEP);
      }

      dev_dbg (hub->intfdev,
            "debounce: port %d: total %dms stable %dms status 0x%x\n",
            port1, total_time, stable_time, portstatus);

      if (stable_time < HUB_DEBOUNCE_STABLE)
            return -ETIMEDOUT;
      return portstatus;
}

void usb_ep0_reinit(struct usb_device *udev)
{
      usb_disable_endpoint(udev, 0 + USB_DIR_IN, true);
      usb_disable_endpoint(udev, 0 + USB_DIR_OUT, true);
      usb_enable_endpoint(udev, &udev->ep0, true);
}
EXPORT_SYMBOL_GPL(usb_ep0_reinit);

#define usb_sndaddr0pipe()    (PIPE_CONTROL << 30)
#define usb_rcvaddr0pipe()    ((PIPE_CONTROL << 30) | USB_DIR_IN)

static int hub_set_address(struct usb_device *udev, int devnum)
{
      int retval;
      struct usb_hcd *hcd = bus_to_hcd(udev->bus);

      /*
       * The host controller will choose the device address,
       * instead of the core having chosen it earlier
       */
      if (!hcd->driver->address_device && devnum <= 1)
            return -EINVAL;
      if (udev->state == USB_STATE_ADDRESS)
            return 0;
      if (udev->state != USB_STATE_DEFAULT)
            return -EINVAL;
      if (hcd->driver->address_device) {
            retval = hcd->driver->address_device(hcd, udev);
      } else {
            retval = usb_control_msg(udev, usb_sndaddr0pipe(),
                        USB_REQ_SET_ADDRESS, 0, devnum, 0,
                        NULL, 0, USB_CTRL_SET_TIMEOUT);
            if (retval == 0)
                  update_address(udev, devnum);
      }
      if (retval == 0) {
            /* Device now using proper address. */
            usb_set_device_state(udev, USB_STATE_ADDRESS);
            usb_ep0_reinit(udev);
      }
      return retval;
}

/* Reset device, (re)assign address, get device descriptor.
 * Device connection must be stable, no more debouncing needed.
 * Returns device in USB_STATE_ADDRESS, except on error.
 *
 * If this is called for an already-existing device (as part of
 * usb_reset_and_verify_device), the caller must own the device lock.  For a
 * newly detected device that is not accessible through any global
 * pointers, it's not necessary to lock the device.
 */
static int
hub_port_init (struct usb_hub *hub, struct usb_device *udev, int port1,
            int retry_counter)
{
      static DEFINE_MUTEX(usb_address0_mutex);

      struct usb_device *hdev = hub->hdev;
      struct usb_hcd          *hcd = bus_to_hcd(hdev->bus);
      int               i, j, retval;
      unsigned          delay = HUB_SHORT_RESET_TIME;
      enum usb_device_speed   oldspeed = udev->speed;
      char              *speed, *type;
      int               devnum = udev->devnum;

      /* root hub ports have a slightly longer reset period
       * (from USB 2.0 spec, section 7.1.7.5)
       */
      if (!hdev->parent) {
            delay = HUB_ROOT_RESET_TIME;
            if (port1 == hdev->bus->otg_port)
                  hdev->bus->b_hnp_enable = 0;
      }

      /* Some low speed devices have problems with the quick delay, so */
      /*  be a bit pessimistic with those devices. RHbug #23670 */
      if (oldspeed == USB_SPEED_LOW)
            delay = HUB_LONG_RESET_TIME;

      mutex_lock(&usb_address0_mutex);

      if ((hcd->driver->flags & HCD_USB3) && udev->config) {
            /* FIXME this will need special handling by the xHCI driver. */
            dev_dbg(&udev->dev,
                        "xHCI reset of configured device "
                        "not supported yet.\n");
            retval = -EINVAL;
            goto fail;
      } else if (!udev->config && oldspeed == USB_SPEED_SUPER) {
            /* Don't reset USB 3.0 devices during an initial setup */
            usb_set_device_state(udev, USB_STATE_DEFAULT);
      } else {
            /* Reset the device; full speed may morph to high speed */
            /* FIXME a USB 2.0 device may morph into SuperSpeed on reset. */
            retval = hub_port_reset(hub, port1, udev, delay);
            if (retval < 0)         /* error or disconnect */
                  goto fail;
            /* success, speed is known */
      }
      retval = -ENODEV;

      if (oldspeed != USB_SPEED_UNKNOWN && oldspeed != udev->speed) {
            dev_dbg(&udev->dev, "device reset changed speed!\n");
            goto fail;
      }
      oldspeed = udev->speed;

      /* USB 2.0 section 5.5.3 talks about ep0 maxpacket ...
       * it's fixed size except for full speed devices.
       * For Wireless USB devices, ep0 max packet is always 512 (tho
       * reported as 0xff in the device descriptor). WUSB1.0[4.8.1].
       */
      switch (udev->speed) {
      case USB_SPEED_SUPER:
      case USB_SPEED_VARIABLE:      /* fixed at 512 */
            udev->ep0.desc.wMaxPacketSize = cpu_to_le16(512);
            break;
      case USB_SPEED_HIGH:          /* fixed at 64 */
            udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
            break;
      case USB_SPEED_FULL:          /* 8, 16, 32, or 64 */
            /* to determine the ep0 maxpacket size, try to read
             * the device descriptor to get bMaxPacketSize0 and
             * then correct our initial guess.
             */
            udev->ep0.desc.wMaxPacketSize = cpu_to_le16(64);
            break;
      case USB_SPEED_LOW:           /* fixed at 8 */
            udev->ep0.desc.wMaxPacketSize = cpu_to_le16(8);
            break;
      default:
            goto fail;
      }
 
      type = "";
      switch (udev->speed) {
      case USB_SPEED_LOW:     speed = "low";    break;
      case USB_SPEED_FULL:    speed = "full";   break;
      case USB_SPEED_HIGH:    speed = "high";   break;
      case USB_SPEED_SUPER:
                        speed = "super";
                        break;
      case USB_SPEED_VARIABLE:
                        speed = "variable";
                        type = "Wireless ";
                        break;
      default:          speed = "?";      break;
      }
      if (udev->speed != USB_SPEED_SUPER)
            dev_info(&udev->dev,
                        "%s %s speed %sUSB device using %s and address %d\n",
                        (udev->config) ? "reset" : "new", speed, type,
                        udev->bus->controller->driver->name, devnum);

      /* Set up TT records, if needed  */
      if (hdev->tt) {
            udev->tt = hdev->tt;
            udev->ttport = hdev->ttport;
      } else if (udev->speed != USB_SPEED_HIGH
                  && hdev->speed == USB_SPEED_HIGH) {
            udev->tt = &hub->tt;
            udev->ttport = port1;
      }
 
      /* Why interleave GET_DESCRIPTOR and SET_ADDRESS this way?
       * Because device hardware and firmware is sometimes buggy in
       * this area, and this is how Linux has done it for ages.
       * Change it cautiously.
       *
       * NOTE:  If USE_NEW_SCHEME() is true we will start by issuing
       * a 64-byte GET_DESCRIPTOR request.  This is what Windows does,
       * so it may help with some non-standards-compliant devices.
       * Otherwise we start with SET_ADDRESS and then try to read the
       * first 8 bytes of the device descriptor to get the ep0 maxpacket
       * value.
       */
      for (i = 0; i < GET_DESCRIPTOR_TRIES; (++i, msleep(100))) {
            /*
             * An xHCI controller cannot send any packets to a device until
             * a set address command successfully completes.
             */
            if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3)) {
                  struct usb_device_descriptor *buf;
                  int r = 0;

#define GET_DESCRIPTOR_BUFSIZE      64
                  buf = kmalloc(GET_DESCRIPTOR_BUFSIZE, GFP_NOIO);
                  if (!buf) {
                        retval = -ENOMEM;
                        continue;
                  }

                  /* Retry on all errors; some devices are flakey.
                   * 255 is for WUSB devices, we actually need to use
                   * 512 (WUSB1.0[4.8.1]).
                   */
                  for (j = 0; j < 3; ++j) {
                        buf->bMaxPacketSize0 = 0;
                        r = usb_control_msg(udev, usb_rcvaddr0pipe(),
                              USB_REQ_GET_DESCRIPTOR, USB_DIR_IN,
                              USB_DT_DEVICE << 8, 0,
                              buf, GET_DESCRIPTOR_BUFSIZE,
                              initial_descriptor_timeout);
                        switch (buf->bMaxPacketSize0) {
                        case 8: case 16: case 32: case 64: case 255:
                              if (buf->bDescriptorType ==
                                          USB_DT_DEVICE) {
                                    r = 0;
                                    break;
                              }
                              /* FALL THROUGH */
                        default:
                              if (r == 0)
                                    r = -EPROTO;
                              break;
                        }
                        if (r == 0)
                              break;
                  }
                  udev->descriptor.bMaxPacketSize0 =
                              buf->bMaxPacketSize0;
                  kfree(buf);

                  retval = hub_port_reset(hub, port1, udev, delay);
                  if (retval < 0)         /* error or disconnect */
                        goto fail;
                  if (oldspeed != udev->speed) {
                        dev_dbg(&udev->dev,
                              "device reset changed speed!\n");
                        retval = -ENODEV;
                        goto fail;
                  }
                  if (r) {
                        dev_err(&udev->dev,
                              "device descriptor read/64, error %d\n",
                              r);
                        retval = -EMSGSIZE;
                        continue;
                  }
#undef GET_DESCRIPTOR_BUFSIZE
            }

            /*
             * If device is WUSB, we already assigned an
             * unauthorized address in the Connect Ack sequence;
             * authorization will assign the final address.
             */
            if (udev->wusb == 0) {
                  for (j = 0; j < SET_ADDRESS_TRIES; ++j) {
                        retval = hub_set_address(udev, devnum);
                        if (retval >= 0)
                              break;
                        msleep(200);
                  }
                  if (retval < 0) {
                        dev_err(&udev->dev,
                              "device not accepting address %d, error %d\n",
                              devnum, retval);
                        goto fail;
                  }
                  if (udev->speed == USB_SPEED_SUPER) {
                        devnum = udev->devnum;
                        dev_info(&udev->dev,
                                    "%s SuperSpeed USB device using %s and address %d\n",
                                    (udev->config) ? "reset" : "new",
                                    udev->bus->controller->driver->name, devnum);
                  }

                  /* cope with hardware quirkiness:
                   *  - let SET_ADDRESS settle, some device hardware wants it
                   *  - read ep0 maxpacket even for high and low speed,
                   */
                  msleep(10);
                  if (USE_NEW_SCHEME(retry_counter) && !(hcd->driver->flags & HCD_USB3))
                        break;
            }

            retval = usb_get_device_descriptor(udev, 8);
            if (retval < 8) {
                  dev_err(&udev->dev,
                              "device descriptor read/8, error %d\n",
                              retval);
                  if (retval >= 0)
                        retval = -EMSGSIZE;
            } else {
                  retval = 0;
                  break;
            }
      }
      if (retval)
            goto fail;

      if (udev->descriptor.bMaxPacketSize0 == 0xff ||
                  udev->speed == USB_SPEED_SUPER)
            i = 512;
      else
            i = udev->descriptor.bMaxPacketSize0;
      if (le16_to_cpu(udev->ep0.desc.wMaxPacketSize) != i) {
            if (udev->speed != USB_SPEED_FULL ||
                        !(i == 8 || i == 16 || i == 32 || i == 64)) {
                  dev_err(&udev->dev, "ep0 maxpacket = %d\n", i);
                  retval = -EMSGSIZE;
                  goto fail;
            }
            dev_dbg(&udev->dev, "ep0 maxpacket = %d\n", i);
            udev->ep0.desc.wMaxPacketSize = cpu_to_le16(i);
            usb_ep0_reinit(udev);
      }
  
      retval = usb_get_device_descriptor(udev, USB_DT_DEVICE_SIZE);
      if (retval < (signed)sizeof(udev->descriptor)) {
            dev_err(&udev->dev, "device descriptor read/all, error %d\n",
                  retval);
            if (retval >= 0)
                  retval = -ENOMSG;
            goto fail;
      }

      retval = 0;

fail:
      if (retval) {
            hub_port_disable(hub, port1, 0);
            update_address(udev, devnum); /* for disconnect processing */
      }
      mutex_unlock(&usb_address0_mutex);
      return retval;
}

static void
check_highspeed (struct usb_hub *hub, struct usb_device *udev, int port1)
{
      struct usb_qualifier_descriptor     *qual;
      int                     status;

      qual = kmalloc (sizeof *qual, GFP_KERNEL);
      if (qual == NULL)
            return;

      status = usb_get_descriptor (udev, USB_DT_DEVICE_QUALIFIER, 0,
                  qual, sizeof *qual);
      if (status == sizeof *qual) {
            dev_info(&udev->dev, "not running at top speed; "
                  "connect to a high speed hub\n");
            /* hub LEDs are probably harder to miss than syslog */
            if (hub->has_indicators) {
                  hub->indicator[port1-1] = INDICATOR_GREEN_BLINK;
                  schedule_delayed_work (&hub->leds, 0);
            }
      }
      kfree(qual);
}

static unsigned
hub_power_remaining (struct usb_hub *hub)
{
      struct usb_device *hdev = hub->hdev;
      int remaining;
      int port1;

      if (!hub->limited_power)
            return 0;

      remaining = hdev->bus_mA - hub->descriptor->bHubContrCurrent;
      for (port1 = 1; port1 <= hdev->maxchild; ++port1) {
            struct usb_device *udev = hdev->children[port1 - 1];
            int               delta;

            if (!udev)
                  continue;

            /* Unconfigured devices may not use more than 100mA,
             * or 8mA for OTG ports */
            if (udev->actconfig)
                  delta = udev->actconfig->desc.bMaxPower * 2;
            else if (port1 != udev->bus->otg_port || hdev->parent)
                  delta = 100;
            else
                  delta = 8;
            if (delta > hub->mA_per_port)
                  dev_warn(&udev->dev,
                         "%dmA is over %umA budget for port %d!\n",
                         delta, hub->mA_per_port, port1);
            remaining -= delta;
      }
      if (remaining < 0) {
            dev_warn(hub->intfdev, "%dmA over power budget!\n",
                  - remaining);
            remaining = 0;
      }
      return remaining;
}

/* Handle physical or logical connection change events.
 * This routine is called when:
 *    a port connection-change occurs;
 *    a port enable-change occurs (often caused by EMI);
 *    usb_reset_and_verify_device() encounters changed descriptors (as from
 *          a firmware download)
 * caller already locked the hub
 */
static void hub_port_connect_change(struct usb_hub *hub, int port1,
                              u16 portstatus, u16 portchange)
{
      struct usb_device *hdev = hub->hdev;
      struct device *hub_dev = hub->intfdev;
      struct usb_hcd *hcd = bus_to_hcd(hdev->bus);
      unsigned wHubCharacteristics =
                  le16_to_cpu(hub->descriptor->wHubCharacteristics);
      struct usb_device *udev;
      int status, i;

      dev_dbg (hub_dev,
            "port %d, status %04x, change %04x, %s\n",
            port1, portstatus, portchange, portspeed (portstatus));

      if (hub->has_indicators) {
            set_port_led(hub, port1, HUB_LED_AUTO);
            hub->indicator[port1-1] = INDICATOR_AUTO;
      }

#ifdef      CONFIG_USB_OTG
      /* during HNP, don't repeat the debounce */
      if (hdev->bus->is_b_host)
            portchange &= ~(USB_PORT_STAT_C_CONNECTION |
                        USB_PORT_STAT_C_ENABLE);
#endif

      /* Try to resuscitate an existing device */
      udev = hdev->children[port1-1];
      if ((portstatus & USB_PORT_STAT_CONNECTION) && udev &&
                  udev->state != USB_STATE_NOTATTACHED) {
            usb_lock_device(udev);
            if (portstatus & USB_PORT_STAT_ENABLE) {
                  status = 0;       /* Nothing to do */

#ifdef CONFIG_USB_SUSPEND
            } else if (udev->state == USB_STATE_SUSPENDED &&
                        udev->persist_enabled) {
                  /* For a suspended device, treat this as a
                   * remote wakeup event.
                   */
                  if (udev->do_remote_wakeup)
                        status = remote_wakeup(udev);

                  /* Otherwise leave it be; devices can't tell the
                   * difference between suspended and disabled.
                   */
                  else
                        status = 0;
#endif

            } else {
                  status = -ENODEV; /* Don't resuscitate */
            }
            usb_unlock_device(udev);

            if (status == 0) {
                  clear_bit(port1, hub->change_bits);
                  return;
            }
      }

      /* Disconnect any existing devices under this port */
      if (udev)
            usb_disconnect(&hdev->children[port1-1]);
      clear_bit(port1, hub->change_bits);

      if (portchange & (USB_PORT_STAT_C_CONNECTION |
                        USB_PORT_STAT_C_ENABLE)) {
            status = hub_port_debounce(hub, port1);
            if (status < 0) {
                  if (printk_ratelimit())
                        dev_err(hub_dev, "connect-debounce failed, "
                                    "port %d disabled\n", port1);
                  portstatus &= ~USB_PORT_STAT_CONNECTION;
            } else {
                  portstatus = status;
            }
      }

      /* Return now if debouncing failed or nothing is connected */
      if (!(portstatus & USB_PORT_STAT_CONNECTION)) {

            /* maybe switch power back on (e.g. root hub was reset) */
            if ((wHubCharacteristics & HUB_CHAR_LPSM) < 2
                        && !(portstatus & (1 << USB_PORT_FEAT_POWER)))
                  set_port_feature(hdev, port1, USB_PORT_FEAT_POWER);

            if (portstatus & USB_PORT_STAT_ENABLE)
                  goto done;
            return;
      }

      for (i = 0; i < SET_CONFIG_TRIES; i++) {

            /* reallocate for each attempt, since references
             * to the previous one can escape in various ways
             */
            udev = usb_alloc_dev(hdev, hdev->bus, port1);
            if (!udev) {
                  dev_err (hub_dev,
                        "couldn't allocate port %d usb_device\n",
                        port1);
                  goto done;
            }

            usb_set_device_state(udev, USB_STATE_POWERED);
            udev->bus_mA = hub->mA_per_port;
            udev->level = hdev->level + 1;
            udev->wusb = hub_is_wusb(hub);

            /*
             * USB 3.0 devices are reset automatically before the connect
             * port status change appears, and the root hub port status
             * shows the correct speed.  We also get port change
             * notifications for USB 3.0 devices from the USB 3.0 portion of
             * an external USB 3.0 hub, but this isn't handled correctly yet
             * FIXME.
             */

            if (!(hcd->driver->flags & HCD_USB3))
                  udev->speed = USB_SPEED_UNKNOWN;
            else if ((hdev->parent == NULL) &&
                        (portstatus & (1 << USB_PORT_FEAT_SUPERSPEED)))
                  udev->speed = USB_SPEED_SUPER;
            else
                  udev->speed = USB_SPEED_UNKNOWN;

            /*
             * xHCI needs to issue an address device command later
             * in the hub_port_init sequence for SS/HS/FS/LS devices.
             */
            if (!(hcd->driver->flags & HCD_USB3)) {
                  /* set the address */
                  choose_address(udev);
                  if (udev->devnum <= 0) {
                        status = -ENOTCONN;     /* Don't retry */
                        goto loop;
                  }
            }

            /* reset (non-USB 3.0 devices) and get descriptor */
            status = hub_port_init(hub, udev, port1, i);
            if (status < 0)
                  goto loop;

            /* consecutive bus-powered hubs aren't reliable; they can
             * violate the voltage drop budget.  if the new child has
             * a "powered" LED, users should notice we didn't enable it
             * (without reading syslog), even without per-port LEDs
             * on the parent.
             */
            if (udev->descriptor.bDeviceClass == USB_CLASS_HUB
                        && udev->bus_mA <= 100) {
                  u16   devstat;

                  status = usb_get_status(udev, USB_RECIP_DEVICE, 0,
                              &devstat);
                  if (status < 2) {
                        dev_dbg(&udev->dev, "get status %d ?\n", status);
                        goto loop_disable;
                  }
                  le16_to_cpus(&devstat);
                  if ((devstat & (1 << USB_DEVICE_SELF_POWERED)) == 0) {
                        dev_err(&udev->dev,
                              "can't connect bus-powered hub "
                              "to this port\n");
                        if (hub->has_indicators) {
                              hub->indicator[port1-1] =
                                    INDICATOR_AMBER_BLINK;
                              schedule_delayed_work (&hub->leds, 0);
                        }
                        status = -ENOTCONN;     /* Don't retry */
                        goto loop_disable;
                  }
            }
 
            /* check for devices running slower than they could */
            if (le16_to_cpu(udev->descriptor.bcdUSB) >= 0x0200
                        && udev->speed == USB_SPEED_FULL
                        && highspeed_hubs != 0)
                  check_highspeed (hub, udev, port1);

            /* Store the parent's children[] pointer.  At this point
             * udev becomes globally accessible, although presumably
             * no one will look at it until hdev is unlocked.
             */
            status = 0;

            /* We mustn't add new devices if the parent hub has
             * been disconnected; we would race with the
             * recursively_mark_NOTATTACHED() routine.
             */
            spin_lock_irq(&device_state_lock);
            if (hdev->state == USB_STATE_NOTATTACHED)
                  status = -ENOTCONN;
            else
                  hdev->children[port1-1] = udev;
            spin_unlock_irq(&device_state_lock);

            /* Run it through the hoops (find a driver, etc) */
            if (!status) {
                  status = usb_new_device(udev);
                  if (status) {
                        spin_lock_irq(&device_state_lock);
                        hdev->children[port1-1] = NULL;
                        spin_unlock_irq(&device_state_lock);
                  }
            }

            if (status)
                  goto loop_disable;

            status = hub_power_remaining(hub);
            if (status)
                  dev_dbg(hub_dev, "%dmA power budget left\n", status);

            return;

loop_disable:
            hub_port_disable(hub, port1, 1);
loop:
            usb_ep0_reinit(udev);
            release_address(udev);
            usb_put_dev(udev);
            if ((status == -ENOTCONN) || (status == -ENOTSUPP))
                  break;
      }
      if (hub->hdev->parent ||
                  !hcd->driver->port_handed_over ||
                  !(hcd->driver->port_handed_over)(hcd, port1))
            dev_err(hub_dev, "unable to enumerate USB device on port %d\n",
                        port1);
 
done:
      hub_port_disable(hub, port1, 1);
      if (hcd->driver->relinquish_port && !hub->hdev->parent)
            hcd->driver->relinquish_port(hcd, port1);
}

static void hub_events(void)
{
      struct list_head *tmp;
      struct usb_device *hdev;
      struct usb_interface *intf;
      struct usb_hub *hub;
      struct device *hub_dev;
      u16 hubstatus;
      u16 hubchange;
      u16 portstatus;
      u16 portchange;
      int i, ret;
      int connect_change;

      /*
       *  We restart the list every time to avoid a deadlock with
       * deleting hubs downstream from this one. This should be
       * safe since we delete the hub from the event list.
       * Not the most efficient, but avoids deadlocks.
       */
      while (1) {

            /* Grab the first entry at the beginning of the list */
            spin_lock_irq(&hub_event_lock);
            if (list_empty(&hub_event_list)) {
                  spin_unlock_irq(&hub_event_lock);
                  break;
            }

            tmp = hub_event_list.next;
            list_del_init(tmp);

            hub = list_entry(tmp, struct usb_hub, event_list);
            kref_get(&hub->kref);
            spin_unlock_irq(&hub_event_lock);

            hdev = hub->hdev;
            hub_dev = hub->intfdev;
            intf = to_usb_interface(hub_dev);
            dev_dbg(hub_dev, "state %d ports %d chg %04x evt %04x\n",
                        hdev->state, hub->descriptor
                              ? hub->descriptor->bNbrPorts
                              : 0,
                        /* NOTE: expects max 15 ports... */
                        (u16) hub->change_bits[0],
                        (u16) hub->event_bits[0]);

            /* Lock the device, then check to see if we were
             * disconnected while waiting for the lock to succeed. */
            usb_lock_device(hdev);
            if (unlikely(hub->disconnected))
                  goto loop;

            /* If the hub has died, clean up after it */
            if (hdev->state == USB_STATE_NOTATTACHED) {
                  hub->error = -ENODEV;
                  hub_quiesce(hub, HUB_DISCONNECT);
                  goto loop;
            }

            /* Autoresume */
            ret = usb_autopm_get_interface(intf);
            if (ret) {
                  dev_dbg(hub_dev, "Can't autoresume: %d\n", ret);
                  goto loop;
            }

            /* If this is an inactive hub, do nothing */
            if (hub->quiescing)
                  goto loop_autopm;

            if (hub->error) {
                  dev_dbg (hub_dev, "resetting for error %d\n",
                        hub->error);

                  ret = usb_reset_device(hdev);
                  if (ret) {
                        dev_dbg (hub_dev,
                              "error resetting hub: %d\n", ret);
                        goto loop_autopm;
                  }

                  hub->nerrors = 0;
                  hub->error = 0;
            }

            /* deal with port status changes */
            for (i = 1; i <= hub->descriptor->bNbrPorts; i++) {
                  if (test_bit(i, hub->busy_bits))
                        continue;
                  connect_change = test_bit(i, hub->change_bits);
                  if (!test_and_clear_bit(i, hub->event_bits) &&
                              !connect_change)
                        continue;

                  ret = hub_port_status(hub, i,
                              &portstatus, &portchange);
                  if (ret < 0)
                        continue;

                  if (portchange & USB_PORT_STAT_C_CONNECTION) {
                        clear_port_feature(hdev, i,
                              USB_PORT_FEAT_C_CONNECTION);
                        connect_change = 1;
                  }

                  if (portchange & USB_PORT_STAT_C_ENABLE) {
                        if (!connect_change)
                              dev_dbg (hub_dev,
                                    "port %d enable change, "
                                    "status %08x\n",
                                    i, portstatus);
                        clear_port_feature(hdev, i,
                              USB_PORT_FEAT_C_ENABLE);

                        /*
                         * EM interference sometimes causes badly
                         * shielded USB devices to be shutdown by
                         * the hub, this hack enables them again.
                         * Works at least with mouse driver. 
                         */
                        if (!(portstatus & USB_PORT_STAT_ENABLE)
                            && !connect_change
                            && hdev->children[i-1]) {
                              dev_err (hub_dev,
                                  "port %i "
                                  "disabled by hub (EMI?), "
                                  "re-enabling...\n",
                                    i);
                              connect_change = 1;
                        }
                  }

                  if (portchange & USB_PORT_STAT_C_SUSPEND) {
                        struct usb_device *udev;

                        clear_port_feature(hdev, i,
                              USB_PORT_FEAT_C_SUSPEND);
                        udev = hdev->children[i-1];
                        if (udev) {
                              usb_lock_device(udev);
                              ret = remote_wakeup(hdev->
                                          children[i-1]);
                              usb_unlock_device(udev);
                              if (ret < 0)
                                    connect_change = 1;
                        } else {
                              ret = -ENODEV;
                              hub_port_disable(hub, i, 1);
                        }
                        dev_dbg (hub_dev,
                              "resume on port %d, status %d\n",
                              i, ret);
                  }
                  
                  if (portchange & USB_PORT_STAT_C_OVERCURRENT) {
                        dev_err (hub_dev,
                              "over-current change on port %d\n",
                              i);
                        clear_port_feature(hdev, i,
                              USB_PORT_FEAT_C_OVER_CURRENT);
                        hub_power_on(hub, true);
                  }

                  if (portchange & USB_PORT_STAT_C_RESET) {
                        dev_dbg (hub_dev,
                              "reset change on port %d\n",
                              i);
                        clear_port_feature(hdev, i,
                              USB_PORT_FEAT_C_RESET);
                  }

                  if (connect_change)
                        hub_port_connect_change(hub, i,
                                    portstatus, portchange);
            } /* end for i */

            /* deal with hub status changes */
            if (test_and_clear_bit(0, hub->event_bits) == 0)
                  ;     /* do nothing */
            else if (hub_hub_status(hub, &hubstatus, &hubchange) < 0)
                  dev_err (hub_dev, "get_hub_status failed\n");
            else {
                  if (hubchange & HUB_CHANGE_LOCAL_POWER) {
                        dev_dbg (hub_dev, "power change\n");
                        clear_hub_feature(hdev, C_HUB_LOCAL_POWER);
                        if (hubstatus & HUB_STATUS_LOCAL_POWER)
                              /* FIXME: Is this always true? */
                              hub->limited_power = 1;
                        else
                              hub->limited_power = 0;
                  }
                  if (hubchange & HUB_CHANGE_OVERCURRENT) {
                        dev_dbg (hub_dev, "overcurrent change\n");
                        msleep(500);      /* Cool down */
                        clear_hub_feature(hdev, C_HUB_OVER_CURRENT);
                              hub_power_on(hub, true);
                  }
            }

loop_autopm:
            /* Allow autosuspend if we're not going to run again */
            if (list_empty(&hub->event_list))
                  usb_autopm_enable(intf);
loop:
            usb_unlock_device(hdev);
            kref_put(&hub->kref, hub_release);

        } /* end while (1) */
}

static int hub_thread(void *__unused)
{
      /* khubd needs to be freezable to avoid intefering with USB-PERSIST
       * port handover.  Otherwise it might see that a full-speed device
       * was gone before the EHCI controller had handed its port over to
       * the companion full-speed controller.
       */
      set_freezable();

      do {
            hub_events();
            wait_event_freezable(khubd_wait,
                        !list_empty(&hub_event_list) ||
                        kthread_should_stop());
      } while (!kthread_should_stop() || !list_empty(&hub_event_list));

      pr_debug("%s: khubd exiting\n", usbcore_name);
      return 0;
}

static struct usb_device_id hub_id_table [] = {
    { .match_flags = USB_DEVICE_ID_MATCH_DEV_CLASS,
      .bDeviceClass = USB_CLASS_HUB},
    { .match_flags = USB_DEVICE_ID_MATCH_INT_CLASS,
      .bInterfaceClass = USB_CLASS_HUB},
    { }                                   /* Terminating entry */
};

MODULE_DEVICE_TABLE (usb, hub_id_table);

static struct usb_driver hub_driver = {
      .name =           "hub",
      .probe =    hub_probe,
      .disconnect =     hub_disconnect,
      .suspend =  hub_suspend,
      .resume =   hub_resume,
      .reset_resume =   hub_reset_resume,
      .pre_reset =      hub_pre_reset,
      .post_reset =     hub_post_reset,
      .ioctl =    hub_ioctl,
      .id_table = hub_id_table,
      .supports_autosuspend = 1,
};

int usb_hub_init(void)
{
      if (usb_register(&hub_driver) < 0) {
            printk(KERN_ERR "%s: can't register hub driver\n",
                  usbcore_name);
            return -1;
      }

      khubd_task = kthread_run(hub_thread, NULL, "khubd");
      if (!IS_ERR(khubd_task))
            return 0;

      /* Fall through if kernel_thread failed */
      usb_deregister(&hub_driver);
      printk(KERN_ERR "%s: can't start khubd\n", usbcore_name);

      return -1;
}

void usb_hub_cleanup(void)
{
      kthread_stop(khubd_task);

      /*
       * Hub resources are freed for us by usb_deregister. It calls
       * usb_driver_purge on every device which in turn calls that
       * devices disconnect function if it is using this driver.
       * The hub_disconnect function takes care of releasing the
       * individual hub resources. -greg
       */
      usb_deregister(&hub_driver);
} /* usb_hub_cleanup() */

static int descriptors_changed(struct usb_device *udev,
            struct usb_device_descriptor *old_device_descriptor)
{
      int         changed = 0;
      unsigned    index;
      unsigned    serial_len = 0;
      unsigned    len;
      unsigned    old_length;
      int         length;
      char        *buf;

      if (memcmp(&udev->descriptor, old_device_descriptor,
                  sizeof(*old_device_descriptor)) != 0)
            return 1;

      /* Since the idVendor, idProduct, and bcdDevice values in the
       * device descriptor haven't changed, we will assume the
       * Manufacturer and Product strings haven't changed either.
       * But the SerialNumber string could be different (e.g., a
       * different flash card of the same brand).
       */
      if (udev->serial)
            serial_len = strlen(udev->serial) + 1;

      len = serial_len;
      for (index = 0; index < udev->descriptor.bNumConfigurations; index++) {
            old_length = le16_to_cpu(udev->config[index].desc.wTotalLength);
            len = max(len, old_length);
      }

      buf = kmalloc(len, GFP_NOIO);
      if (buf == NULL) {
            dev_err(&udev->dev, "no mem to re-read configs after reset\n");
            /* assume the worst */
            return 1;
      }
      for (index = 0; index < udev->descriptor.bNumConfigurations; index++) {
            old_length = le16_to_cpu(udev->config[index].desc.wTotalLength);
            length = usb_get_descriptor(udev, USB_DT_CONFIG, index, buf,
                        old_length);
            if (length != old_length) {
                  dev_dbg(&udev->dev, "config index %d, error %d\n",
                              index, length);
                  changed = 1;
                  break;
            }
            if (memcmp (buf, udev->rawdescriptors[index], old_length)
                        != 0) {
                  dev_dbg(&udev->dev, "config index %d changed (#%d)\n",
                        index,
                        ((struct usb_config_descriptor *) buf)->
                              bConfigurationValue);
                  changed = 1;
                  break;
            }
      }

      if (!changed && serial_len) {
            length = usb_string(udev, udev->descriptor.iSerialNumber,
                        buf, serial_len);
            if (length + 1 != serial_len) {
                  dev_dbg(&udev->dev, "serial string error %d\n",
                              length);
                  changed = 1;
            } else if (memcmp(buf, udev->serial, length) != 0) {
                  dev_dbg(&udev->dev, "serial string changed\n");
                  changed = 1;
            }
      }

      kfree(buf);
      return changed;
}

/**
 * usb_reset_and_verify_device - perform a USB port reset to reinitialize a device
 * @udev: device to reset (not in SUSPENDED or NOTATTACHED state)
 *
 * WARNING - don't use this routine to reset a composite device
 * (one with multiple interfaces owned by separate drivers)!
 * Use usb_reset_device() instead.
 *
 * Do a port reset, reassign the device's address, and establish its
 * former operating configuration.  If the reset fails, or the device's
 * descriptors change from their values before the reset, or the original
 * configuration and altsettings cannot be restored, a flag will be set
 * telling khubd to pretend the device has been disconnected and then
 * re-connected.  All drivers will be unbound, and the device will be
 * re-enumerated and probed all over again.
 *
 * Returns 0 if the reset succeeded, -ENODEV if the device has been
 * flagged for logical disconnection, or some other negative error code
 * if the reset wasn't even attempted.
 *
 * The caller must own the device lock.  For example, it's safe to use
 * this from a driver probe() routine after downloading new firmware.
 * For calls that might not occur during probe(), drivers should lock
 * the device using usb_lock_device_for_reset().
 *
 * Locking exception: This routine may also be called from within an
 * autoresume handler.  Such usage won't conflict with other tasks
 * holding the device lock because these tasks should always call
 * usb_autopm_resume_device(), thereby preventing any unwanted autoresume.
 */
static int usb_reset_and_verify_device(struct usb_device *udev)
{
      struct usb_device       *parent_hdev = udev->parent;
      struct usb_hub                *parent_hub;
      struct usb_device_descriptor  descriptor = udev->descriptor;
      int                     i, ret = 0;
      int                     port1 = udev->portnum;

      if (udev->state == USB_STATE_NOTATTACHED ||
                  udev->state == USB_STATE_SUSPENDED) {
            dev_dbg(&udev->dev, "device reset not allowed in state %d\n",
                        udev->state);
            return -EINVAL;
      }

      if (!parent_hdev) {
            /* this requires hcd-specific logic; see OHCI hc_restart() */
            dev_dbg(&udev->dev, "%s for root hub!\n", __func__);
            return -EISDIR;
      }
      parent_hub = hdev_to_hub(parent_hdev);

      set_bit(port1, parent_hub->busy_bits);
      for (i = 0; i < SET_CONFIG_TRIES; ++i) {

            /* ep0 maxpacket size may change; let the HCD know about it.
             * Other endpoints will be handled by re-enumeration. */
            usb_ep0_reinit(udev);
            ret = hub_port_init(parent_hub, udev, port1, i);
            if (ret >= 0 || ret == -ENOTCONN || ret == -ENODEV)
                  break;
      }
      clear_bit(port1, parent_hub->busy_bits);

      if (ret < 0)
            goto re_enumerate;
 
      /* Device might have changed firmware (DFU or similar) */
      if (descriptors_changed(udev, &descriptor)) {
            dev_info(&udev->dev, "device firmware changed\n");
            udev->descriptor = descriptor;      /* for disconnect() calls */
            goto re_enumerate;
      }

      /* Restore the device's previous configuration */
      if (!udev->actconfig)
            goto done;
      ret = usb_control_msg(udev, usb_sndctrlpipe(udev, 0),
                  USB_REQ_SET_CONFIGURATION, 0,
                  udev->actconfig->desc.bConfigurationValue, 0,
                  NULL, 0, USB_CTRL_SET_TIMEOUT);
      if (ret < 0) {
            dev_err(&udev->dev,
                  "can't restore configuration #%d (error=%d)\n",
                  udev->actconfig->desc.bConfigurationValue, ret);
            goto re_enumerate;
      }
      usb_set_device_state(udev, USB_STATE_CONFIGURED);

      /* Put interfaces back into the same altsettings as before.
       * Don't bother to send the Set-Interface request for interfaces
       * that were already in altsetting 0; besides being unnecessary,
       * many devices can't handle it.  Instead just reset the host-side
       * endpoint state.
       */
      for (i = 0; i < udev->actconfig->desc.bNumInterfaces; i++) {
            struct usb_interface *intf = udev->actconfig->interface[i];
            struct usb_interface_descriptor *desc;

            desc = &intf->cur_altsetting->desc;
            if (desc->bAlternateSetting == 0) {
                  usb_disable_interface(udev, intf, true);
                  usb_enable_interface(udev, intf, true);
                  ret = 0;
            } else {
                  ret = usb_set_interface(udev, desc->bInterfaceNumber,
                              desc->bAlternateSetting);
            }
            if (ret < 0) {
                  dev_err(&udev->dev, "failed to restore interface %d "
                        "altsetting %d (error=%d)\n",
                        desc->bInterfaceNumber,
                        desc->bAlternateSetting,
                        ret);
                  goto re_enumerate;
            }
      }

done:
      return 0;
 
re_enumerate:
      hub_port_logical_disconnect(parent_hub, port1);
      return -ENODEV;
}

/**
 * usb_reset_device - warn interface drivers and perform a USB port reset
 * @udev: device to reset (not in SUSPENDED or NOTATTACHED state)
 *
 * Warns all drivers bound to registered interfaces (using their pre_reset
 * method), performs the port reset, and then lets the drivers know that
 * the reset is over (using their post_reset method).
 *
 * Return value is the same as for usb_reset_and_verify_device().
 *
 * The caller must own the device lock.  For example, it's safe to use
 * this from a driver probe() routine after downloading new firmware.
 * For calls that might not occur during probe(), drivers should lock
 * the device using usb_lock_device_for_reset().
 *
 * If an interface is currently being probed or disconnected, we assume
 * its driver knows how to handle resets.  For all other interfaces,
 * if the driver doesn't have pre_reset and post_reset methods then
 * we attempt to unbind it and rebind afterward.
 */
int usb_reset_device(struct usb_device *udev)
{
      int ret;
      int i;
      struct usb_host_config *config = udev->actconfig;

      if (udev->state == USB_STATE_NOTATTACHED ||
                  udev->state == USB_STATE_SUSPENDED) {
            dev_dbg(&udev->dev, "device reset not allowed in state %d\n",
                        udev->state);
            return -EINVAL;
      }

      /* Prevent autosuspend during the reset */
      usb_autoresume_device(udev);

      if (config) {
            for (i = 0; i < config->desc.bNumInterfaces; ++i) {
                  struct usb_interface *cintf = config->interface[i];
                  struct usb_driver *drv;
                  int unbind = 0;

                  if (cintf->dev.driver) {
                        drv = to_usb_driver(cintf->dev.driver);
                        if (drv->pre_reset && drv->post_reset)
                              unbind = (drv->pre_reset)(cintf);
                        else if (cintf->condition ==
                                    USB_INTERFACE_BOUND)
                              unbind = 1;
                        if (unbind)
                              usb_forced_unbind_intf(cintf);
                  }
            }
      }

      ret = usb_reset_and_verify_device(udev);

      if (config) {
            for (i = config->desc.bNumInterfaces - 1; i >= 0; --i) {
                  struct usb_interface *cintf = config->interface[i];
                  struct usb_driver *drv;
                  int rebind = cintf->needs_binding;

                  if (!rebind && cintf->dev.driver) {
                        drv = to_usb_driver(cintf->dev.driver);
                        if (drv->post_reset)
                              rebind = (drv->post_reset)(cintf);
                        else if (cintf->condition ==
                                    USB_INTERFACE_BOUND)
                              rebind = 1;
                  }
                  if (ret == 0 && rebind)
                        usb_rebind_intf(cintf);
            }
      }

      usb_autosuspend_device(udev);
      return ret;
}
EXPORT_SYMBOL_GPL(usb_reset_device);


/**
 * usb_queue_reset_device - Reset a USB device from an atomic context
 * @iface: USB interface belonging to the device to reset
 *
 * This function can be used to reset a USB device from an atomic
 * context, where usb_reset_device() won't work (as it blocks).
 *
 * Doing a reset via this method is functionally equivalent to calling
 * usb_reset_device(), except for the fact that it is delayed to a
 * workqueue. This means that any drivers bound to other interfaces
 * might be unbound, as well as users from usbfs in user space.
 *
 * Corner cases:
 *
 * - Scheduling two resets at the same time from two different drivers
 *   attached to two different interfaces of the same device is
 *   possible; depending on how the driver attached to each interface
 *   handles ->pre_reset(), the second reset might happen or not.
 *
 * - If a driver is unbound and it had a pending reset, the reset will
 *   be cancelled.
 *
 * - This function can be called during .probe() or .disconnect()
 *   times. On return from .disconnect(), any pending resets will be
 *   cancelled.
 *
 * There is no no need to lock/unlock the @reset_ws as schedule_work()
 * does its own.
 *
 * NOTE: We don't do any reference count tracking because it is not
 *     needed. The lifecycle of the work_struct is tied to the
 *     usb_interface. Before destroying the interface we cancel the
 *     work_struct, so the fact that work_struct is queued and or
 *     running means the interface (and thus, the device) exist and
 *     are referenced.
 */
void usb_queue_reset_device(struct usb_interface *iface)
{
      schedule_work(&iface->reset_ws);
}
EXPORT_SYMBOL_GPL(usb_queue_reset_device);

Generated by  Doxygen 1.6.0   Back to index